Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Webinar

 
Labels

Forum Posts

Resolved! ASA 5505 wan link

hi everyone,i'm a bit confused about the smallest member of the asa family, and i couldn't find any solid info regarding this. what do i need to connect to the fa0/0 (default "outside" vlan) in order to get a wan connection? can it be a simple dsl mo...

Hi, I've been ask to configure interfaces on my 3560, but they want them asinterface gigEthernet2/0/1!interface gigEthernet2/0/2etcI only seeinterface gigEthernet0/1!interface gigEthernet0/2This "2" I assume is the sub-interface from a trunk? How do...

whiteford by Level 1
  • 631 Views
  • 3 replies
  • 0 Helpful votes

I have two Routers connected with Two different ISP. Both connected with Layer 3 switch. I have applied Policy base routing on layer switch. Now when switch sending few subnets towards ISP B and few subnets are going to ISP A.But problem is that, my ...

Had this message on my router - all other PIX etc equipment has remained up 1 year + This router is internet facing and performs NAT and failover.ErrorInternet-GW uptime is 1 week, 1 day, 5 hours, 29 minutesSystem returned to ROM by address error at...

The connection between side A and side B has 3 routers (router A, router B and router C). Currently, there is a problem to do the network load balancing so that most of the network traffic will go through router A and B from side A to side B. However...

ssweehin by Level 1
  • 874 Views
  • 8 replies
  • 0 Helpful votes

Hi I am having 3 sites/locations (SITE-A,B & C), SITE-A is having two routers, SITE-B is having 1 router & SITE-C is having 2 routers I am having 4 subnets at SITE-A out of 4 2 nos each are connected behind each router.I had attached the current OSPF...

Hi I have the following config that work's just great but i am unable to telnet into the device remotely. I have tried setting the telnet interface to Dialer1 but this does not work plus have also tried the following access list, that also does not w...

dionh by Level 1
  • 1665 Views
  • 15 replies
  • 0 Helpful votes

Hi All, If DLCI are locally significant as defined by Frame-relay studies, how then would my local DLCI knows where the traffic should be directed?. Considering that we have hundreds of DLCIs in the frame-relay cloud.I am not talking of p-2-mlt...

Hi,Just about to buy a couple of Server Access Switches.Toying between the 4948 or 3750E.Its for servers in the DataCentre, so accrding to Cisco I should go for the 4948 ..however, all the talk is around the 3750s ..... like these are the NEXT BIG TH...

mcroft by Level 1
  • 569 Views
  • 1 replies
  • 0 Helpful votes

We have a client with a 3825 router with an NM-4T. They are using port 0,1,2 in a ppp multilink bundle. They having slow bandwidth issues and the all of the ports on the NM-4T are showing carrier transitions, even port 3 which does not have anythin...

ereinoehl by Level 1
  • 3345 Views
  • 3 replies
  • 0 Helpful votes

Hi, I currently have a cisco 1841 router and i'm trying to upgrade it to ips v5 sigshowever it seem that it won't let me, all it will accept is the .sdf files, i'm running ios c1841-adventerprisek9-mz.124-18.binhowever it doesn't seem to support the ...

ddolbel by Level 1
  • 900 Views
  • 6 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card