Resolved! Broadcast in HSRP Topology
Hi , I just wanted to know how will the broadcast behave in case of hsrp topolgy,I have attached the diagram and shown with arrows that broadcast will flow ! Any suggestions to avoid this?
Hi , I just wanted to know how will the broadcast behave in case of hsrp topolgy,I have attached the diagram and shown with arrows that broadcast will flow ! Any suggestions to avoid this?
we have the task to connect an ethernetsubinterface to a switch where our provider is connected.the provider expects 6mb/s of traffic from our router.because the ethernetinterface is 100mb/s, we have to configure hirachical queueing because we ave qo...
We are installing a router to access the internet and ASA firewall to protect the internal network. Are access list required in the above case, how would it be used, what would the access list(s) protect? The servers would have private IP addresses....
I am facing a problem with 2 T1's in a multilink bundle.There are lot of drops if we do a ping to the other side of the multilink. IF we remove one of the links, then the response is fine. The link shows no errors when it is not part of the bundleand...
Hello I have a 1760 series router that is coming up withWarning: monitor nvram area is corrupt....using default valuesCan anyone provide ant further information concerning this error. Is there any memory test that I can do to verify nvram memory if c...
I have a cisco 2610 with a WIC1-ADSL card, and the c2600-is4-mz version of IOS installed......My problem, I do believe, is in configuration. If I show interface adsl 0/0, it shows that there are packets being sent and received. On the BVI1 interface,...
Hi, I have got a Cisco 877w working in VPN mode on a DSL line I have to my Head Office. I have configured the wireless as well on WPA/TKIP and and I can wirelessly connect to my Head office via wireless.Now I want to secure things down more if possi...
I am having problems getting CiscoWorks to see the Cisco IP phones. The locations has the following devices, Cisco 2851 Integrated Services Router with a 2800 Series 16-Port EtherSwitch Service Module. The IP phones are DHCP. Is there a config statem...
Dear allMy company use one line (leaseline 2Mb)for all services(internet,vpn,webclient,mail server, data server).Now I have a new line (leaseline 1Mb) from other ISP.I want to connect 2 that line in one router 2800 and I have one Pix 515E inside and ...
We currently have the following setup:2 - 2501 routers connected via a leased T1 line between our branch location and our main location.1 Cisco 1720 router at our branch location connected to our ISP.1 Cisco 1720 router at our main location connected...
This router runs IOS 11.1, see attempt to add route below - it just fails as if the command does not exist:Router>enPassword:Router#conf tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#ip route 0.0.0.0 0.0.0.0 Serial0 ...
Sir I want to know about the ping response characters. How many are there and what do they show.
Hi,I am configuring a 1721 router for Internet access for a branch office with 30 employees. There will be a ASA5505 firewall behind the 1721. The ISP has provided 14 public Ethernet IP addresses. Is it more efficient to perform PAT or NAT? Is it ...
%ALIGN-3-TRACE: -Traceback= 402B4DA4 40ACAB98 40AC9238 401E9B44 401E9B30 00000000 00000000 00000000Can someone assist with this?
Hi,I am setting up a new network. Is NAT configured on the perimeter router, or the ASA5505 firewall?Thanks.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-26-2025 02:24 AM | ||
| 10-24-2025 11:24 AM | ||
| 10-16-2025 11:52 AM | ||
| 10-15-2025 06:33 PM | ||
| 10-15-2025 04:37 PM |
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 1 | |
| 1 | |
| 1 |