HellomI seem to be having trouble advertising a prefix list to a BGP neighbor.Could anyone shed some light pls.Attached below captures the list of OSPF routes i have in the routing table. I have this redistributed onto BGP.O 10.40.0.32/30 [110/...
Forum Posts
Resolved! Cisco 1K IPSEC Performance Limitation
According to Cisco 1000 Series Integrated Services Routers Ordering Guide - Cisco The SEC license , for example , SL-1100-4P-SEC provides up to 50 Mbps IPsec performance. Does this mean 50M upload and 50M download at the same time ? in other words , ...
HejWe have some ASR9903s version 24.2.2We want to advertise connected routes in a L3VPN to other routers with same VRF in our network except few routes. For example, how can I advertise all connected routes except anything within 16.0.0.0/16 in a VRF...
Hi, I'm trying to configure my ISR 4331 router. I'm configuring the management port to use it as the port connecting to my internal routers through iBGP. I have put an IP on the port and have connected a cable to it. But when I try to ping the IP I p...
Hi, I have an ISR4451 with multiple IPSEC tunnel configured on my outside interface. How do I shutdown a specific tunnel? I could use the remote peer to specify the tunnel but not sure of a command to disable it. The other side is with a vendor using...
Hi,I am using C921 router, 1 WAN port connected to ISP & other WAN port connected VPN. Some website access only through VPN port only. I want to do URL specific route through WAN Port of VPN.
Hi everyone,I have some questions regarding MPLS, I work with a transport company and am wondering is there any configuration must set from our company side regarding MPLS on the router or that is a ISP thing?The ip address handled to up from ISP are...
Resolved! BGP TCP Session
Hi Can anyone tell how to find which router first initiate the TCP session in BGP. Thanks in Advance.
Resolved! Routing issue | OSPF and Static
Dear Team, We are looking for a solution for the following issue. As illustrated in the attached diagram, there is an existing P2PRouting, connection between Site 1 and Site 2 using two separate ISPs. Currently, traffic from Site 2 is routed through ...
Resolved! ISR 4431 from version 16.9.5 to 17.9.5?
I've read the documentation Cisco 4000 Series ISRs Software Configuration Guide, Cisco IOS XE 17 which says "When you upgrade from Cisco IOS XE 3.x to 16.x image, you should first upgrade the rommon release to the 16.7(5r) rommon release. After upgra...
I am about to finish this packet tracer lab, but the only thing is that the wireless router is not letting me finish is that the starting ip address for the DHCP server should be 10.10.10.50 and when I try to put it, it will automatically change to 1...
Resolved! Product Number details
Dear Team, Request to share product number details for below mentioned serial number.Make: CiscoModel: 3945ESerial Number: FOC17460PVYRegards,Indrani.RM
Hello I have a Check-Point virtual firewall in the network, connected to router, with a 0.0.0.0 route pointing towards the router. When the Check-Point needs to update, it traffic through the router, which performs NAT to an external IP. Now, the ...
Hello,I am running a little LAB on CML 2.7.2. I have the following topology: I am prepending a mix of public and private ASN on R2 towards R3:and I am also using the command to remove all the private ASN from the AS-PATH attribute on routes advertise...
Hello,we have a strange problem with our Cisco ISR4431/K9 router. There is a VM behind it, which is trying to connect a server in Internet.We have a NAT configuration on the router which allows all other clients to connect to Internet resources witho...
