Hello!How can I bridge two T1 routers? Or How can I configure the two T1 routers to act as a bridge?Thanks,Jorge
Hello!How can I bridge two T1 routers? Or How can I configure the two T1 routers to act as a bridge?Thanks,Jorge
Hi everybodyi have the following network topology:172.168.10.32/27---R1---192.168.4.4/30----R2----172.168.10.64/27when update timers for both routers then the router's update begin , incrementing the routes by one and send them to each other...after ...
Hi Experts,Can any one tell me the advantage of Path MTU Discovery? What are the pros and cons? Is there global configuration command or is there any routing protocol specific command?Cheers,Nik
Friends,Can you please let me know what are the common modem types used these days for Leased lines, FR etc. Are there any good links that I can refer too. I want to understand the different signals and buttons available in a modem. Also how does the...
Dear All,Anybody know the contact address for Cisco NetPro forum!! i need to report vert strange issue happened in my profile, so if anybody know such contact please help.Best Regards,Mounir Mohamed
HiCan somebody explain me why there can only be HSRP configured on a maximum of 32 vlans on a catalyst 3750?So, I have 40 vlans and I can not configure HSRP on each vlan. Thanks
I created a few video tutorials for dynamips router emulation software and its front-end (dynagen) for those that are interested.http://www.blindhog.net/category/dynamips/Enjoy!
Hi there.We have a Cisco 1801 which we have only just bought. It works well for a few minutes and the CD light comes on, then it decides that it has lost connection, and resynchs to the line. Sometimes this works and the connection comes back up, oth...
I have a pix 501 which has a public outside address, and a private inside address. Everything works perfectly until there is 10 minutes of idle time...after that I can't even ping the public side of the pix. If I log into the PDM and ping a differe...
Good morning. I have been suffering through an issue with our DMVPN tunnels for the last year or more and finally decided to try and get some help.The issue is if a tunnel goes down it does not always recreate itself automatically. I need to telnet ...
I need some help guys. I have a config that I need to know what the dscp marking will be when it leaves the router serial sub interface. Can someone tell me, from the config below, what the packet will be marked as when it leaves? Thanks.ip access...
Hi, i have link problems since i replaced a 7200 with PA-E3s with a 7600 with SIP/200&SPA-4XT3/E3. The perfectly working link with 7200, never goes up/up with the SPA. Also the SPA does not recognize a hardware looping (cable). Tried 2 SPA modules. I...
Dear Sir,Is there any web site to provide the service to check the GBP as-path from internet? Best regardsCM Leung
Hi,This is about PBR.If I have two WAN links to same ISP who provides me two LAN Subnets and I want to control the inbound/outbound traffic as;1. Traffic to/from LAN SubnetA uses Link1 as primary and Link2 as backup.2. Traffic to/from LAN SubnetB use...
in usual congestion queue (diffserv) i usually create defined class. for ex: class http is allocated 50kbps while class ftp has 20 kbps and else is priority queue for voice with upper 30kbps. my link is 256kbps and to benefit from rsvp i want to res...
| 主题 | 作者 | 发布日期 |
|---|---|---|
| 03-26-2025 12:57 AM | ||
| 03-25-2025 06:10 PM | ||
| 03-24-2025 10:17 AM | ||
| 03-22-2025 09:39 PM | ||
| 03-07-2025 07:44 AM |