Greetings, I've deployed a new Cisco CSRr1000v(Cisco IOS XE Software, Version 17.03.04a) VM on Proxmox and tried to access the web interface, but it's taking a long time to load. It had the same loading issue when I did the same deployment before, ho...
Forum Posts
I have to communicte site 1 to site 5 without communicate ospf domain.So i got solution by using gre tunnel from r2 to r5.but i have problem with r2.I have configured ospf and eigrp route in r2. I didnt want to communicte 141.88.83.36 & 37 as per my...
- FYI : https://www.cisco.com/c/en/us/support/docs/field-notices/722/fn72246.html M.
Hi, I need a documentation guide step by step to downgrade IOS XR from 7.1.15 x64 in ASR9910. We have tried with USB boot and tftp boot still failed. show install active summary Fri Jun 19 09:53:16.327 UTCActive Packages: 2asr9k-xr-7.1.15 version=7...
Resolved! can anyone help on this topology
1. Configure the devices according the diagram. Run EIGRP protocol in Site 1 and Site 5 Run OSPF protocol in Site 7 Make sure that after completing the configuration Site 1 and site 5 should communicate each other but Site 7 should not get a...
We are having an issue with our Internet edge routers looping some IP blocks between them. Curious if anyone has any input. Below is a super simple diagram of the setup. [ISP A] [ISP B] | EBGP | EBGP[Router A] <--...
Resolved! Unable to enable OSPF and EIGRP
I am new to OSPF and EIGRP, I am trying to enable OSPF and EIGRP.1. On OSPF in config mode i type CISCO3560(config)#router ospf 1CISCO3560(config)# it does not return the prompt CISCO3560(config-router)#2 For EIGRP T type CISCO3560(config-if)#CISCO3...
hi,Does anyone know when was the following command's meaning changed in IOSXE - next-hop-unchanged Documentation says following ( which seem to be pointing that the nexthop will remain unchanged for ebgp )- To enable an external BGP (eBGP) peer that...
So I have my VRF lite setup in the WLC 9800 oddly enough that includes VLAN(Mobile clients) and Interface twoGi0/0/0 out to the ISP. I cannot however get DHCP. The DHCP server is behind VLAN on the corp network, as we have to have it windows based d...
Hello everyone, i'm trying to solve this problem that is very difficult for me because i'm not a Cisco user.Anyway, i have this situation, the schema it has been simplified:The WindowsClient must use some service on WindowsServer via IP 192.168.150.2...
Hi all, hope to find everyone wellI'm currently having a really, weird, weird issue with a Cisco 3650 with the SVI 10.5.40.254 and some equipment. Basically, I have some radios connected to this switch where the radio is 10.5.40.39 and this radio isl...
Resolved! Can't ping
Hello!I am starting a lab where I will be implementing several protocols.To start with, I am just trying to get all the equipment to communicate.I have 3 routers on the left and 3 on the right and a Switch symbolizing a carrier.To separate the traffi...
Hi In this router, the tunnel is inactive for long time. Checking the tunnel and its interface facing outside, it shows no any traffic. The strange thing is the router shows the interface 39.2.2.2 is up via show ip int bri, but the router cannot ping...
I append the new acl (number "9681") into existing ACL "ACL-AVCSS-in-3" (The ACL was applied in TenGigabitEthernet1/1/4 and TenGigabitEthernet1/1/4) on Apr 27 17:44:50. However, the track "%TRACK-6-STATE: 1 ip sla 1 state Up -> Down" and %TRACK-6-STA...
I've just configured a new internal subnet which I can ping from the router but I can't ping devices on the subnet from my computer. I have other subnets configured and they work fine. For example:WORKS - can ping from both router and PC:interface Gi...
