Routing

I have a new 2801 that uses both a T1 via S 0/2/0 and a DSL modem in transparent bridge mode via FE 0/1. The T1 works fine, however I can't get any packets to go out the DSL interface. FE 0/1 is configured to use a PPPoE connection, and it appears ...

Head end router(3845) is connected to five remote sites via individual T1s. Customer wants to move all the T1 connections from the remote sites to a DS3 cloud and move the head end router to a DS3 so that the Head end router would have a single DS3 c...

Hi,I have 836 router . Ping test with 2000 mtu is absolutly fine ( ping count 1000) but when mtu =1500, lots of drops..Unable to understand that ..ThxG

just wanted to know one thing........what is the rule abt standard and extended access-list....like it should be placed near to source or destination......just confuse abt that an dwhy is that.....thanks in advance....cheers

HiI'm finding a probem with laptops with 802.11g cads integrated.The scenario is that we have several 802.11b AP's and one 802.11g AP. All of them are 1100 and 1200.The problem is that laptops with a 802.11g card makes wrong decisions to connect when...

I just purchased a 2611XM from ebay for $460 bucks and I'm having problems with it hanging on bootup. Can anyone help me out with some things I could try to fix this ? It boots occasionally, mostly it hangs on boot, usually at the same place. I am no...

Hi ,is there any way I can find if an interface supports jumbo frames ?Using any command ...Thanks in advance ,Thomas.

Trying to configure VWIC-1MFT-E1 for ISDN data on new 3845 (12.4(3c)with advancedipservices)When I try to configure pri-group timeslots its says.% Not enough DSP resources available to configure pri-group on controller E1 0/1/0% The remaining dsp res...

Hi, I would like to know the command for checking the BW utilization of a DS3 link which is terminating on a Catalyst switch port. For this link we have configured the IP and others in MSFC through a VLAN inteface. But sh int vlan "#" is not giving t...

Need help please. Have 5 Vlans on 2970 switch that is communicating with the 3750 L3 . On the 2970 I need to find out which PC/Computer is connected to lets say port 20 of the 2970. Since 2970 is a Layer 2 switch, how can I achieve my goal , I think ...

I am having an issue with a DSL link running PPPOE over Ethernet and NAT on a 1720 router. The 1720 router has (1) T! interface and (2) Ethenret interfaces. My internal clients use a spoofed IP address. When they go to the internet they go through a ...

For some reason Snort and Ethereal is not seeing source IP's that are from outside of my Network. When I go to a website, Snort and Ethereal picks it up, but it does not see any of the return packets. I am able to surf fine and have ruled out switch ...

Will a 4507 switch accept an output QOS policy that contains CLASS percentages for bandwidth allocation? On 65XX switches and wan routers, i can do something like:policy-map pol-blahclass VOICEpriority percent 5class GOLDbandwidth percent 30The "ban...

Hi All,I am applying (Policy-Map) rate limiting on my router subinterfaces for dedicated bandwidth, I would like to know: how long is the average statistics of the interface when you issue the command (sh policy-map int g6/2) for example? also is the...

How can I redistribute an E2 route from OSPF to BGP?Here is the config so far:address-family ipv4 vrf arena_201 redistribute connected redistribute static redistribute ospf 900 no auto-summary no synchronization exit-address-familyHere are the routin...