Hello,I would like to know how to disable http so when I go to http://192.168.1.1, I dont want see userid & password prompt.
Hello,I would like to know how to disable http so when I go to http://192.168.1.1, I dont want see userid & password prompt.
Hello,I would like to know how to disable http so when I go to http://192.168.1.1, I dont want to userid & password prompt.
R1, R2 & R3 are fully meshed with R1 & R3 learning EBGP routes from another two AS ? R2 has no EBGP peers.When I configure R1, R2 & R3 with no synchronization they each show all the IBGP routes advertised by their IBGP peers and these routes are ente...
We just hooked up a IGX 8430 32 slot rackmount chassis. Slots 1-16 work fine and slots 17-32 show up as "empty".When cards are plugged into the lower shelf (slots 17-32) we get ""Empty 31 HW failure" (31 beingthe among the slot we tried)". The SCM ...
Brand new 1841 router. Connected to the console and ran through the initial setup, changing the enable secret and enable passwords. After setup I did a conf term and entered the following - no username cisco, then wrote the config to memory. The r...
I?m trying to connect a branch office to head office using two 1841?s across a T-1 line.I?ve got communication between the routers across the T-1 using a static route, and from each router to the locally attached Ethernet LAN. I do not have communica...
Hi All,Can someone tell me the difference between doing the following:ip route 10.0.0.0 255.255.255.0 FastEthernet1/0andip route 10.0.0.0 255.255.255.0 10.0.0.1I did the first one on my router to begin with and it did not work, but the second did. W...
Hello,I am in the process of ordering a 3800 series router for Japan. I've never ordered internet connection out-of-US before. what are some of the concerns I should be addressing with Japan's ISP?I also would like to know what WIC is appropriate f...
Hi,I have a problem with a site to site vpn connection between a dg834g and a cisco 1803. Everything works for about 3min then stops and comes back for 3ish mins. The only thing i can see is this error message :-DPD: No response from peer - declaring...
Hello,I would like to know how to disable http so when I go to http://192.168.1.1, I dont want to userid & password prompt.
I have a dual homed AS using to eBGP connections, through one of the connections I can access hotmail.com but through the other link I can't access the hotmail.com unless I change the MTU in users PCs or in the PROXY server.If one have any experience...
Hi,I have a question regarding GRE tunnel interface over Internet DSLs, encrypted using IPSec. We use below config:interface Tunnel1 bandwidth 1000 ip address <ip> <mask> no ip redirects ip mtu 1272 ip nhrp authentication <auth_profile> ip nhrp map <...
Hi, if you are looking to change the MTU size of a link, do you have to do this at the same time for all connections along a path between a source and destination? In this case the source and destination are within the same AS.Thanks
Maybe someone has some experience with SBC (AT&T) DSL? I cannot seem to get the ATM Interface to come up. I called SBC and checked through all of my settings, Changed the cable, etc. I know that I am missing something. Any thoughts or help would be g...
Following is my setupRA---- Router ARB----- Router BRC----- Router CRC-512kbpslink--RA--2Mbps ink-RB-128Kbps-RCRA is connected to RC with 512 kbps link and RA is also connected to RB with 2 Mbps link.Again RB is connected to RC with 128 link.we are r...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 03-26-2025 12:57 AM | ||
| 03-25-2025 06:10 PM | ||
| 03-24-2025 10:17 AM | ||
| 03-22-2025 09:39 PM | ||
| 03-07-2025 07:44 AM |
| User | Count |
|---|---|
| 12 | |
| 9 | |
| 8 | |
| 6 | |
| 6 |