Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Webinar

 
Labels

Forum Posts

I have a site that has an isdn backup. My problem is once the primary line goes down the isdn line gets taxed and is unusable by the staff who use session based software(telnet app). The sites consist of 2 subnets a public subnet and a private subnet...

h.wall by Level 1
  • 795 Views
  • 3 replies
  • 0 Helpful votes

Hello,I need to send all my voip traffic using a single ISP router (bgp peer). We'll be load balancing to 4 peers on the same AS.Connection are done via fastethernet, our core 4506 connects to a layer 2 device and then to the ISP peers (all ethernet)...

Hi,I have to check if in Cisco 7200 router there are bgp session flapping without charging the cpu and I had an idea using the bgp dampening command.Now, if someone used it, if this command introduces cpu load.Thank you.Regards.Paolo

Resolved! Static routes

Question for you....I have a cisco 2600 with 2 static routes going to the same subnet:ip route 192.168.81.0 255.255.255.240 192.168.180.1ip route 192.168.81.0 255.255.255.240 192.168.204.2 2I noticed that it always takes the 180.1 route even though 2...

Warren by Level 1
  • 1588 Views
  • 8 replies
  • 0 Helpful votes

Hi guys,Can someone enlighten me on these command. Im using this command on my ibgp. Will this command make the router the next-hop if that router is connected and configured for ibgp ?INTERNET--Router(next-hop-self)--IBGP --- Internalrouter --- myne...

In a lab setup, I have two routers (routers B and C) in the middle running iBGP and on either side a router (A and D) running EIGRP. Now in order to have full connectivity, I did a mutual redistribution of BGP into EIGRP and vice versa on routers B a...

giamwi by Level 1
  • 910 Views
  • 6 replies
  • 0 Helpful votes

We will have two internet access setup.Here is diagram:Location A (10MB Verizon):10MB (internet) <--> 3640Router <--> 3650Switch <--> PIX 525 <-->4507RLocation B (100MB Internet Verizon)100MB (internet) <--> 2811Router <--> 3650Switch <--> ASA 5520 <...

jolo07310 by Level 5
  • 445 Views
  • 5 replies
  • 0 Helpful votes

QOS

Dear All, I want to deploy QOS on Cisco 1700 router for implementing Video Conferencing .Can somebody guide on same ?regds,Aman

amansoi_5 by Level 1
  • 336 Views
  • 1 replies
  • 0 Helpful votes

We are running OSPF; we have PIX 525 protecting our server farm. OSPF process is running fine on PIX. PIX have established adjacencies with switches and routers on the same segment and show full neighbor relationships with all devices. All Interfaces...

umar-rana by Level 1
  • 921 Views
  • 4 replies
  • 0 Helpful votes

HI ALL!I've sumarized toward the core from each dist.i;m a little bit confused about the routing loop;the routing P is EIGRP.CAN U use static route to the null0.how is the procedure.PS Have a look to my config&the attachment:core: router eigrp 100 ne...

alsayed by Level 1
  • 1233 Views
  • 12 replies
  • 0 Helpful votes

hi ihave read in that book that in order to have a neibour relationship the process id and the area shd be same......i ahve connected 3 routers in my lab and i have given 2 routers the same process id and one with the different process id......but st...

Hi!I'm using nat overload.Everything works fine except one or two PC cann't get internet someitmes.When I use clear ip nat trans * then internet are working on that PC however after some times it agian creating problem.i've used translation timeout ...

schakra by Level 1
  • 657 Views
  • 1 replies
  • 0 Helpful votes

I am in need of some help choosing a router that will be appropriate for my current needs. I need a router that can take at least 6 different and seperate internet connections. What will work for me?

DanielO by Level 1
  • 258 Views
  • 1 replies
  • 0 Helpful votes
Unanswered Topics
Review Cisco Networking for a $25 gift card