Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

acl help

hi all,i have the followinig in my router, i only want the web and the cisco vpn to work. when i apply these, it stops so apparently i am doing somethign wrong! can someone help? thanks!!access-list 2 remark <name>access-list 2 permit <ip> 0.0.0.2...

rhltechie by • Level 1
  • 1141 Views
  • 8 replies
  • 0 Helpful votes

PPPoE over trunked interface

HiI am trying to establish a PPPoE connection using a 2811 and accompanying 16 port etherswitch module (i.e. plug a dsl modem in bridged mode into one of the etherswitch ports and get the router to establish the PPPoE connection) - would anyone know ...

rate-limit parameter calculation

hi all,i have doubt related how to configure the rate-limit.my doubt is related to normal burts and excess burts. in rate limit do we need to specify bits ,or convert them into bytes and them specify. example i have to limit ftp with speed of 1mb (1...

amitbatra by • Level 1
  • 890 Views
  • 3 replies
  • 0 Helpful votes

OSPF

i have bit confused can some one plz help me out:suppose we have 3 routers which r located in three different sites (melbourne, hongkong, uk) i have dedicated link between them with class c ips.......and running ospf on them.now tell me two things i ...

Routing Protocols

Please any one tell me which routing protocol is most reliable protocol, and in which type of network we uses which routing protocolthax

ahmad2340 by • Level 1
  • 460 Views
  • 1 replies
  • 0 Helpful votes

IP SLA "failed operation" question

We have 3825 router (vestion 124-5a) which has 2 connections to our ISP. The primary link has static route to y.y.y.y (ISP's DG) and "IP SLA" is monitoring this route with these commands.Please see the related configs below. ip sla monitor 1 type ...

r.perera by • Level 1
  • 1953 Views
  • 5 replies
  • 0 Helpful votes

ABRs and Summary LSAs

Hello,I would appreciate if someone could validate my observations on how Internal routers choose summary LSAs heard from two ABRs.It seems as though if an Internal router is directly attached to the ABRs it will use both LSAs. (also assuming metric ...

dwyerr by • Level 1
  • 1317 Views
  • 5 replies
  • 0 Helpful votes

Resolved! EIGRP summary routes

So I'm trying to figure out how to advertise an Eigrp summary route out and interface without installing it into my own routers routing table. Any suggestions welcome.Patrick

BGP's MED attribute

Hi,If a customer is having two uplinks & 2 downlinks, totally based on static routes, now the cust wants to peer with that ISP using BGP, now can he use MED to steer traffic-typeA through one downlink & Traffic-typeB through 2nd downlink & how to dis...

nedian123 by • Level 1
  • 689 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Routing Policies Redundant?

Hello,I want to implement a routing policy that forces all traffic with a certain destination port down one specific link of two wan links. However, should that one link go down, I would want traffic to roll over the other wan link. Is this possibl...

Resolved! Frame relay tc question

Reading on frame relay I can see that the time interval is for most of the providers 1/8 sec, which is 125 ms.I'm trying a couple of configs on my lab I'm running into the following dilemma.Please seethe config below:interface Serial0 bandwidth 1544 ...

Redundant Routing per tcp port number

Hello,I have redundant routing in place with per-connection routing. But I am having problems with certain applications. We have a server (192.168.200.34) that clients on the other end access. I have a route for this address to always take the sam...

Load more