Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Webinar

 
Labels

Forum Posts

I have five retail outlet and one warehouse and i wonder if i can connect all the retail outlet router to the router in Outlet #1. Some of the outlet is as far as 150 km. If i would like to connect all the outlet to the router in Oulet #1, does that ...

winsonlee by Level 1
  • 522 Views
  • 3 replies
  • 0 Helpful votes

Manage switch allow remote configuration for network administrator. If i have an office in perth and another office in sydney, can the network administrator in sydney configure the switch located in perth ??

winsonlee by Level 1
  • 427 Views
  • 1 replies
  • 0 Helpful votes

Hello,I have configured ip rtp header compression on my network:This is the output from the show command:CE-CF-Aveiro#sh ip rtp header-compression multilink 1RTP/UDP/IP header compression statistics:We're compressing using MQC profiles, use theMQC c...

patcbr600 by Level 1
  • 407 Views
  • 2 replies
  • 0 Helpful votes

I am talking about backup configuration on two different routers here. I have one router on which DDR is configured and one other router with Dialer Watch. On the router with simple DDR configuration I can typically ping the AS5300 IP address and bri...

We currently have a Cisco 1721 Router on a T1, we are planning to upgrade to a Bonded T1 in the coming weeks. Can someone recommend which Router 1800 or 2600 series to upgrade to. We have apx.30-40 PCs onsite connected with high streaming video/data ...

Hello Guys,I'm currently studying the CCNA curriculum.I have a questions regarding subnetting which i cannot figure out.I have an ip address : 192.165.x.0 too 192.165.64.0.The questions posed by my instructor:1)what are the odd numbers for this netwo...

We purchased a 871W router thinking that we could use it as follows:The router would connect to the Internet behind a cable modem or DSL modem in a Home Office.The firewall feature set would create a VPN tunnel to our VPN3005 Concentrator and all tra...

mikeh by Level 1
  • 505 Views
  • 2 replies
  • 0 Helpful votes

Hi, While I went through the product specs it spoke about half rate speed for T3/E3 support. Does this mean it would not support a full rate T3 / E3 connection on the backpane? Also given a choice betweem HSSI and T3/E3 Interface which would be the...

Hi all,I need to configure a stun between 2 routers.Both routers can ping each other and both E1s are UP on each side.The pb is that both tunnels stay always closed ..Any ideas ??Thks

feberle by Level 1
  • 722 Views
  • 3 replies
  • 0 Helpful votes

Hello, I'am Carlos, I'am from Venezuela and my english is not very good, but i need your help. The problem is that i have a cisco WS-C6506 with this configuration:interface Vlan1 ip address 161.196.136.129 255.255.255.128 secondary ip address 161.196...

Resolved! BGP routes

A Chairde, I have a 7609 Core Router connected to 10 + networks in a hub spoke configuration, and use BGP as routing protocol. Have setup each network with seperate AS, but am getting complaints that the routers in AS have all routes fro...

crumdub12 by Level 1
  • 668 Views
  • 4 replies
  • 0 Helpful votes

hello.there is a router run eigrp and ospf, and when redistribute from eigrp to ospf, only route learned from other neighbors, which mean didn't redistribute its own route ( directly connected ), could somebody explain what kind of situation is this ...

ikizoo4 by Level 1
  • 429 Views
  • 3 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card