Routing

dear all,system(192.168.10.1)-->router1 e0(192.168.10.2)--->router1 s0(10.1.1.1)-------router2 s0 (10.1.1.2)-->router2 e0(172.16.1.1)--system(172.16.1.2)my query is , when packet moving from source 192.168.10.1 to destination 172.16.1.2 , how the pac...

Dear all,is there a possiblity to convert an image "c1600-y-l.122-31" to "c1600-y-mz.122-31"? We were using it on a 8MB flash card until it broke when moving to another office. Fortunately we had a backup but no spare 8MB Flash cards, only 4MB. Thank...

One of my model 803 routers is showing some strange behavior concerning its IOS version. It claims to be running 12.0(3)T1, but claims the image file is TinyROM-1.4(1). The running behavior feels like proper IOS 12.0.I have attached a file with a

Please, is it possible to configure nat to translate address on two differents class on same router ? How ?for example:RTA eth0/0 (WAN)194.202.232.1195.202.232.1eth0/110.1.1.1We want a specfic sunet of network 10.0.0.0 to be transalte on 194.202.232....

I'm redistributing from BGP into EIGRP and want to tag some routes with one tag and others with another. So, far when I try this the next router sees it with all the same tag. Is it possible to have 2 different tags? The config was similar to the ...

hi, all:i would like to ask if the following is posible and if you can supply a config sample.i have an mgx-8250 working as a ppp edge concentrator. i have redundant rpm's.for this setup i have configured an E1 and addcon directly to one of the RPMs....

hi,I was trying to configure MPLS VPNs on Cat 3550, but I experienced some problems. When I create 2 or more VRF, I get too many packet losses on those VRFs. So without any VRF it works fine, when I add a VRF it again works as it is supposed to work....

I have a router connected over ATM to a field CCTV camera.10.10.1.226 is a MPEG 4 encoder.192.168.253.2 is a software MPEG 4 decoder running on Windows XP (firewall is off)This circuit and these devices are for transporting CCTV video from the field ...

Greetings all,I was wondering if anyone was able to point me in the right direction... I've got a 2611 that's using a static route to forward inbound requests on port 80 to my webserver, which is on the LAN behind the router...Instead of an LVS (virt...

Is the following supported on a 2620 router: NM-HDV-2E1-60. If not what 2600 family do support it. Does it also need a 2MFT-E1. What IOS does this require. I've searched cisco but it is not clear to me.

HelloI ve a "small" problem, I have no more IOS on the flash memory on a cisco 827 router. So I think I should not reboot it .The problem is that I have only a guest account on cisco.com, so I can't download the IOS.What can I do in order to resolve ...

Greetings,I have several remote offices. Each remote office router has 2 links coming back to the main office: dual T1 ATM IMAs connecting to a 6509 and single T1s connecting to a 7507. All traffic goes across the ATM links, even when they're saturat...

I have configured an accounting functionality on a 7609 sup7203bxl. The accounting is based on the class-base QoS MIB.I have attached the service policies on several VLAN interfaces, the VLANs go out over the same 10 GE interface. Question:What is th...

Hi Will the configured BC figure affect the frame size to be transmitted (e.g. MTU)?For example, there is one switch configured as: class important police 10000 1000 5000 conform-action transmit exceed-action dropWill the packet exceeding 1000 b...