In the output of "show Interface" for serial lines I can see the DLY (Delay) value.Where is this value coming from? Is it measured by the IOS itself? Or is it to be set manually?Thanks
In the output of "show Interface" for serial lines I can see the DLY (Delay) value.Where is this value coming from? Is it measured by the IOS itself? Or is it to be set manually?Thanks
Folks, Does someone remember the command to send a message to other people logged into the cisco router at the same time???Thanks
Hi all;i have cisco 2522 rtr; and on ethernet we have two ip, one is 10.155.146.xxx and 10.194.0.xxx(secondary). now i want to do bandwidth sharing between this two ip which assign to ethernet. which will share my serial link of 64 kbps as 60 % and 4...
Can anybody explain me the output of the "show ip interface brief"?In particular I wasn't able to find any documentation on the "OK?" and "Method" columns. For the Method in particular what's the difference between "NVRAM" "unset" and "manual"?Thanks...
Hi,Two 1841 routers are connected over 2 continents with an E1 line using VWIC-1MFT-G703 controllers. The configured channel-group generates a serial interface, which uses hdlc as the default protocol. I notice a standard ping round-trip-delay of at ...
Please help me in this scenario .The Scenario is, i hav PIX 515E with 2 fastethernet ports 100 Mpbs.and a 4503 switch with supervisor engine IV. and a module with 6 fiber ports,All 6 fiber ports have been usedNow i want to connect PIX with switch , b...
i have a problem with nat. we have a router where both inside static and dynamic nat and outside source static nats are configured.now my problem is we have 2 outside interfaces(one primary link on leased line and another backup link on isdn (f...
I think there is no module available for 2800 series router with which we can have more routed ethernet ports. Does anyone know if we can use such network module of old 3600 series router?Thanksregardsrakesh======
!policy-map shapeclass class1banwidth 120class class-defaultfair-queue!interface serial 1/0:0frame-relay traffic-shapinginterface serial 1/0:0.555ip address .....frame-relay class test555frame-relay interface-dlci 555!map-class frame-relay test555ser...
i hav an E1 line to connect abt then 10 sites.is this card VWIC-1MFT-E1 card channelized ?
From Chandra Prakash,I have very old 3102 (EOL) Router with 1 serial port and this should be used as DTE only . So pls suggest me how i can use this for me to setup with RAD modem Thanks in advanceChandra Prakash
I'm tryint to apply qos to our frame-relay links. Rferencing this documenthttp://www.cisco.com/en/US/tech/tk652/tk698/technologies_configuration_example09186a0080094af9.shtmlI'm using software vers. 123-14.T3 The problem I am having is that when I ap...
Could somebody tell me what's performance of 3845? I can't find out the detail information of 3845 in the cisco web site.
Hi all,I am facing a problem with my ISIS, the adjaceny fails and when show logging the following shows, is it a physical problem (which i doubt), or is it ISIS timers and delay problem, or what ?Sep 1 18:35:24: %LINEPROTO-5-UPDOWN: Line protocol on...
I would like to know if anyone has run across this rx_no_eop_err error. I have two sites connecting via point to point serial and on the upstream side I show this error when I issue the sh controller s2/2 command. The upstream shows the link as up do...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-09-2025 06:19 PM | ||
02-06-2025 12:03 AM | ||
02-03-2025 09:24 PM | ||
02-03-2025 07:43 PM | ||
01-13-2025 09:53 AM |
User | Count |
---|---|
15 | |
8 | |
8 | |
7 | |
5 |