Routing

Reading the recently published "Nbar Citrix PDLM readme" it almost leads one to believe that there is/will be a Citrix Version 9 PDLM available. It is unclear if you need to upgrade routers to 12.4(2)T in order to take advantage of the Version9 PDLM...

Not sure how to setup my 2811 to connect to the T1 - Frame relay line to the outside world.Current 1601 interface configs:interface Ethernet0 description to local lan ip address 206.1.2.33 255.255.255.224 no ip directed-broadcastinterface Serial0 ...

how can i divide incoming traffic between serial and ethernet interfacess on router. router is 2600 series and IOS is 12.0 .in other word how can i load balance traffic in the way describe above.Scenario: A Large ISP is providing bandwith to a Small ...

Hi,We have cisco 2811 routers in IOS 12.3(14)T2.Is it possible to install in the same router an ISDN module NM-1CE1T1-PRI, and an ISDN card WIC-1BS/T.I ask this question regarding isdn configuration. If it is possible to have in the cli the configura...

I got 1 cisco 1750 router with WIC-1ADSL, the problem is I cant connect internet very well, that means, I only have maxmum 15Kb/s with some download software(it could be 1mb/s with other modem) and cant use IE for internet(my IE is no problem when I ...

Hi,On Ospf is it possible to increase cost/distance for specific external address type5/7, without increase all the external addressees as this can be done “distance ospf external xxx” .I’m running Ospf and Rip with overlapping IP address hence I wan...

I have a couple of questions about WFQ.WFQ divides the traffic up into conversations, (like flows), and allocates a queue to each one. Typically you have 256 max conversations. The allocation of a flow to a conversation is determined by a hash func...

Trying to build a config that will allow users on 192.168.1.0/24 out except when going to 192.168.20.0/24 and 172.31.1.0/24.ip nat pool NATPOOL 10.10.10.16 10.10.10.19 netmask 255.255.255.252ip nat inside source list 51 pool NATPOOL overloadaccess-li...

dear allis here anybody who can help me deciding by whitch module should i begin preparing my ccnp the first,the second ..and so on..(BSCI,troubleshooting,BCMSN ,BCRAN)and why ?thanks in advancebest regards

Hi all, I have an 8 Port PRI (PA-MC-8TE1) that we would like to use all 8 ports for backup. Card is installed in a 7206VXR with the I/O 2FE and NPE-400. Memory is 512M and IOS is 12.3-13a. When I configure the ports (controllers) with the "pri-g...

Hello.I need some help to understand the output of show buffers command. At Big buffers and VeryBig buffers appear informations in "misses", "trims" and "created" like:Big buffers:14368763 hits, 631 misses, 348 trims, 348 created66 failures (0 no mem...

I have a 1760, that must have had a surge or something. When i try to console into it, this is all I get:îÅ6…Ç:»' gÿò̬øm ¶£tþÔ6þÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ...

I have remote network connected to a central site with a T1 connection that is prone to go down. At the remote site I have a static default route pointing to the router at the central site, the problem is that when the T1 goes down it looks like I ha...

Dear All,I need solution to e following problemThee is router on my network working as ADSL Gateway RR, and the users connect to this router and authentication through PPP session then thay assinged ip from Local pool which already configured on the...

Hi, On Ospf is it possible to increase cost/distance for specific external address type5/7, without increase all the external addressees as this can be done “distance ospf external xxx” . I’m running Ospf and Rip with overlapping IP address hence I w...