Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
Hi team, We are getting high cpu utilization on cisco 2821 Router. Could you suggest on this.=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2020.07.05 00:17:13 =~=~=~=~=~=~=~=~=~=~=~=ter len 0MH-NMVIKROLI-NMDC-RT-C2861-1.146#sh invMH-NMVIKROLI-NMDC...
Hi. Can anyone share how to configure port Bridge in Cisco ISR 4221/K9
Can someone help me with this issue?I have a ISRs 1000 C1121X-8PLTEP and the card P-1T was introduced before turn On the router, the card keeps in booting state.The router C1121X-8PLTEP and the card P-1T is new.Thank you!show platformChassis type: C1...
please can someone help clarify this for me, i need only the system under IT and MANGT to be able to route to all other system and switches.
So lets say for a moment we have 3 routes that exactly the same 192.168.12.0/24 using EIGRP192.168.12.0/27 using RIP192.168.12.0/28 using OSPF From my understanding Administrative distance should be first choosing the EIGRP route If all of these whe...
I'm new in the Networking field. So, maybe my question is dumb, forgive me for that.My question is - Can we use OSPF without backbone area??
Citrix EDT requires users to listen on port UDP 1494I cannot find anywhere whether NBAR classifies this as Citrix, everything I can find just mentions TCP 1494any ideas
Hi All, I have a client who has 2 vlans. Van 1 is the clients general devices PC's printers, Apple TVs etc.. and they have 8 Sonos recently installed. They have a Control system (Crestron) which on the 2nd Vlan wiht a number of wall mounted touchpa...
Topology above: green area being backbone and blue area being area 2. My other network in area 1 (not shown here), summarises properly (this is my 192.168.X.X network) on the ASBR. However, the blue network does not. The routing table maintains every...
Hopefully this can be done. I have tirelessly looked through the forums and tried to see if others can do the same and tried different configs but no go. Here is what I am trying to do.I have a USG Router with 2xWAN ports and 1xLAN port WAN1 = ETH0 ...
Ok...I'm trying to setup my 851W router. Unable to gain access from the LAN port on 10.10.10.1 I'm able to access through the console port, but the default username/passcode (cisco/cisco) does not work. I've tried the reset button, but still no...
What do each of these terminologies mean? Object Network, Mpf(modular policy framework), embryonic What does this command do? set connection per-client-max "" per-client-embryonic ""Why is inspection disabled for ICMP & Traceroute by default in ...
hi,i got a BGP WAN with dual stack IPv4 and IPv6 address. can i configure the same BGP policy/route-map (local pref) applied on IPv4 AF to IPv6?router bgp 65000bgp router-id 1.2.3.4bgp log-neighbor-changesno bgp default ipv4-unicastneighbor 2001:1111...
Hello Cisco Team, I am using Static NAT to make my internal server accessible from Internet.My WAN IP is *.*.*.117 255.255.255.248My Server LAN IP is 10.132.62.25 I am using CISCO 2811 router.WAN IP on int fe0/1 ip nat outside LAN IP on int fe0/0 ip ...
Hi I want to add one more giga-port to Cisco 3845 but all slots are occupied " 3825: 2 used / 0 Free "is there other module with more Giga WAN port can swap besides NM-1GE thx
.jpg "Hall of Fame Master"){kind=icon}
.jpg "VIP Collaborator"){kind=icon}
