We have ISR 4300 Series router without APPX licence, but it requires APPX license.We have same model of Router with APPX licence, which is not required in this Router. This Router is fixed for specific functionality which is not replaceable.So we ne...
Forum Posts
We have a L3VPN MPLS core connecting several sites. each site has one or more T1s connecting into a Cisco ISR 4331 with a nim-4mft-T1/E1 card. My question is how to transport that T1 to another site over the MPLS core? We are just trying to find...
Hello Expert,Our router was flag during an audit for having both ssh v 1.99 and ssh v2.00 running.when I do sh ip ssh the following below :- testf-1#sh ip sshSSH Enabled - version 2.0Authentication methods:publickey,keyboard-interactive,passwordAut...
I am using packet tracer for the first time, I have started to build a network and am stuck due to not being able to see full screen display when selecting a device. I am not able to see the top portion with the category options. i did not change any...
I been having this doubt in this scenario. I have to two sites DMVPN spoke each of them. As you can see the network 10.25.138.0 are on both sites which is the inside network is this possible or will there be a conflict. Spoke-1router eigrp 100network...
Hi MY AS connected to two ISPs If I need to do load balancing to other sites ( per destination not per subnet ) I think about adding Max-path for outbound traffic, for inbound if I use a community to inform both ISPs will it work, ?I read the article...
Currently we have a subnet setup that is not routed. All units just talk to each other inside the Vlan and everything is fine. Now the user needs the vlan routed ONLY to a specific destination that is at another location. Basically they want 10.2...
Resolved! Inetrface
Hello, I'm beginner in networking and could you please explain if I have interface with 100 mbps in this case I can download and upload with 100 mbps speed at the same time? Or it's means that sum of download and upload traffic? If ISP Provide for m...
I have 2 default route.ip route 0.0.0.0 0.0.0.0 1.1.1.1 250ip route 0.0.0.0 0.0.0.0 2.2.2.1 251 I would like to use 2.2.2.1 default route for 1 subnet 10.10.9.0/24 and the rest of the subnets will use the 1.1.1.1 as their primary default route. 10.10...
Resolved! unable to create int vlan xxx
I am unable to create int vlan xxx on ISR 4331 router, its not recognizing the cmd: int vlan ? R1(config)#int vlan ?% Unrecognized commandVlan1 unassigned YES unset administratively down down kindly advice
Resolved! QoS for Voice/Video
I am Planning to Implement QoS for Voice/Video traffic, Please suggest below config would be fine to start with or there is any improvemnts can be done on it ,, Appriciate your support. class-map match-all VIDEOmatch ip dscp af41class-map match-all V...
Resolved! Nat on stick Cisco ISR 4331
hi all, i try to set up NAT on stick on ISR 4331 like it described in the article - https://www.cisco.com/c/en/us/support/docs/ip/network-address-translation-nat/6505-nat-on-stick.html But unfortunately it doesn't operate. I see that route-map is wor...
hii guys I intend to upgrade the IOS of C1111 router , I downloaded a new image (the existing one is “Cisco IOS XE Software, Version 16.10.3a”) and I put it in the flash:, but when I wanted the prompt to start from the new image , I did not find the ...
Hello, Even after all the searchings I've made, I still have a question whether ISR4221 SEC/K9 supports SSL VPN (aka webvpn)or not?From what I found out only ASA's have SSL VPN support, but I also found that it is expected to have SSL VPN supported o...
