Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...

translator.png Asolution.png htlm-source.png insertcode(1).png
Kelli Glass by Community Manager
  • 10256 Views
  • 7 replies
  • 16 Helpful votes

hi everyone, i have a problem with my router, i need to connect it via wan and use it like a normal router, i can configure the wan, i can ping some sites, but if i connect my pc via ethernet to the g0 i don't have any connection, and if i try to con...

hi,i'll be standardizing AAA using TACACS+ (ISE) on IOS-XR 9Ks. right now it's just doing AAA authentication.just want to have a similar look on classic IOS for AAA.can someone confirm if below template is all that's needed?is the 'console' redundant...

I have one DMVPN spoke site that stopped working a few days ago with no changes on the network at the spoke nor the hub. It's encrypted with a certificate so I pulled a new certificate no problem. That shows port 80 to the hub is fine. But I'm not se...

   Hi, I'm new to the networking academy. I've tried to get the 'triangle routers' to ping each other but not as intended to be succeeded. Is there any problem with my configuration? Router 1enconfig tint fa0/0ip add 172.16.1.1 255.255.255.0no shutdo...

asdfasdfasdfasdfasdf.jpg

Hi wifi champions :)I am migrating the old config from 8540 to 9800 but I am scrapping my head around Service Instance List which was available on the old one. I could define there which device is visible where ( location, ap, ap group) Whare is such...

Hello, One of our many NIM-4G-LTE-ST modules seems to have developed some invalid flash contents. We suspect this module lost power during an IOS XE upgrade, wherein XE was silently attempting to upgrade NIM flash during initial bootup after reload. ...

tkapela12 by Level 1
  • 822 Views
  • 1 replies
  • 5 Helpful votes

Hi folks, I'm seeing this command on an interface and trying to understand it's function: interface GigabitEthernet0/0/0ip address x.x.x.x 255.255.255.252ip nat outsideip access-group vpn_in inload-interval 30negotiation autocrypto map VPNend---There...

Hello- I followed the password recovery procedures in the link below, however once I switched register back to 0x2102 it seems I lost my configurations. Password Recovery I'm wondering if when I did write mem (step 16) that deleted my configs. Does a...

Tony T. by Level 1
  • 869 Views
  • 3 replies
  • 0 Helpful votes

Hi all, hope you can help me.I've been hitting with my head trying to put a VPN L2TP with IPsec Policy to work but I haven't been able to.Basically I have a Draytek router (LAN IP 10.14.99.99) connected to a Cisco Router via the Wan 1 port  (WAN IP 1...

Othacon by Level 1
  • 443 Views
  • 0 replies
  • 0 Helpful votes

we have an iWAN infrastructure that uses frontdoor vrf on the internet interface.  the inside client devices can access the internet just fine but at one of our sites we have some internal services that we need to expose to the internet (public web p...

bgoulet00 by Level 1
  • 2498 Views
  • 15 replies
  • 0 Helpful votes

Question, can intervlan routing be done a 6807 layer 3 switch by way of SVIs? I was reading a configuration guide (6800 series) on the cisco site and there is a mention of ISL and other methods which all mention using subinterfaces. Do not want to ev...

abarb002 by Level 1
  • 826 Views
  • 4 replies
  • 0 Helpful votes