Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
Hello! We're really struggling to get cellular connectivity working. We've tried an 887VAMG (c880data-universalk9-mz.154-3.M4.bin) and a 881G-4G (15.9). We've tried them with a 3 (three.co.uk) SIM and a BT (ee) SIM. It feels like we've tried every pe...
Hello.I have nexus 6000 for small data center.Can I connect ISP use BGP (full view)?Thank You!
HelloI have problem with properly configured router-map in Cisco ASR-902 (RSP2). My configuration is following:interface TenGigabitEthernet0/1/0 no ip address service instance 108 ethernet encapsulation dot1q 108 rewrite ingress tag pop 1 symme...
Hello community, I'm doing a troubleshooting and the following message appears in Router BR %ADJ-5-PARENT: Midchain parent maintenance for IP midchain out of 0 65E900C0 - looped chain attempting to stack%TUN-5-RECURDOWN: 0 temporarily disabled due t...
I am looking for some suggestions please. Attached is a basic design for a network with a Router, Transparent Firewall and Layer 2 switch. The mandate is the push some traffic through the Firewall which is limited to 250Mbps throughput and other tr...
Hi Everyone. I've been tasked to design and build a network for an organization with 5 - 10 locations connecting to a central head office. The head office will house a modest data center that will have applications/servers providing services to the b...
Hi, I have a new ASR-9901-120G router. I noticed MAJ LED and all interface port is showing RED light. When inter-connected fiber patch cord to 2 port having GLC-LH-SMD transceiver. The status show up.May I know is it a normal behaviour that all inter...
Dears,I've configured VRF-Lite on RY with BGP Route leaking.BGP AS number on RX, RY & RZ are same.I'm trying to advertised routes of RZ to RX.RY have multiple VRF:VRF A: towards RZVRF B: towards LAN (Firewall)VRF C: towards RX Route leak between VRF ...
Hello,question about BGP IGP tag:On Cisco when i'm doing [aggregate-address summary-only] command the summary route is created by BGP is with IGP tag. Even when no of suppressed routes has an IGP flag. But the RFC says:ORIGIN attribute: If at least ...
Hi.Expieriencing some increasing timeouts on ip virtual-reassembly GigabitEthernet0/0/2.202: Virtual Fragment Reassembly (VFR) is ENABLED [in] Concurrent reassemblies (max-reassemblies): 16 Fragments per reassembly (max-fragments): 32 Reassembly tim...
Lets say I have two IPSec connections on a ISR4k router:crypto isakmp key aaaaaaaaaaaaaaaaaa address 192.168.1.1 255.255.255.255 crypto isakmp key bbbbbbbbbbbbbbbbbb address 192.168.2.2 255.255.255.255 Is it safe to add now one of the following lines...
Dear All, This is my first time here and I would like an advice/help on this little project I created. I am studying for the CCENT (via a course on udemy.com), and I created this project to practice some commands, but this project I made in Packet Tr...
Hi all, I have a configuration with default route injection on NSSA area: area 31 nssa default-information-originate no-summary This announce seems is always active. It is not related to default route presence on route table. So seems that "always"...
Hi,I would need some help with a NAT problem.With some previous help from this community I configured a Cisco ISR 1113-8p, but I cannot allow users from outside my LAN to access to some hosts inside my LAN. They're getting a "connection refused". mes...
Hi,I have a problem on cisco C892. At the moment I apply a ACL-IN ACL on external Dialer0 int, I lose the connectivity from LAN to internet (ping, dns, http, everything), which is unwanted. While I still have RDP access from internet 2.2.2.0 network ...
