We've run into a problem and I'm hoping someone here has at least seen it and can offer some advice or a solution going forward. We have an ISR 4331 with a NIM-ES2-4 module in it. For the longest time, it only had the built-in G0/0/0 and G0/0/1 in...
Forum Posts
Hello, I have a problem with my Cisco RV110W router. When I use it in gateway mode through PPPoE, it limit my internet speed to 50Mbps.I have internet connection thought PPPoE from my ISP up to 100Mbps, and if I put lan cable directly to lan card in ...
Do Cisco Routers (2851) strip or modify DSCP tagging?
Can anybody tell me how to perform a modem power cycle on IOS XE 16.06? The "test cellular 0/2/0 modem-power-cycle " command doesn't appear to exist and I haven't found a command reference with a different command option.
Hello guys, first time I post something here but i'm confused.For class, i have a project which requires me to have, at some point, 2 routers. One "main" router and a backup one. I'm using HSRP. The problem is that on my backup router, one interface ...
Hi, i am investigating some issues on an existing network topology and i have some questions related to the topology.Can someone please support me to understand the concept ? See below some informations: we have 2 catalystics routers connected from 3...
Hello,I have a PBX Asterisk server, which is behind NAT, a Cisco 1921 router.I want to forward multiple ports to it but I found that it is not as easy as in linux using iptables.I thought this command would be appropriate:ip nat inside source static ...
Hi! I have a problem with eigrp and dmvpn. I have a router used as hub for dmvpn. It has a /24 mask on the tunnel interface, but due to continuosly increasing network, I need to make the mask /22. So I prepared some new spokes. So at first I had 1.1....
I currently use redistribute static subnets route-map on IOS how do I configure this on an ASR 9k -See belowrouter ospf 10router-id 192.168.254.2redistribute static subnets route-map NETWORK_REDISTRIBUTEnetwork 10.21.30.0 0.0.0.3 area 0 Access listip...
Resolved! SSH to Public IP ISR Problem
I have a Cisco ISR 1111 with a public IP address. I have dozens of micro sites setup like this but it's got me stumped. Based on sanitized debug attached - you can see SSH SYN comes to the router, the router processes that and sends the reply traffic...
I am doing a last minute test of My Cisco 1111 ISR to make sure I can SSH to is and getting the error above. I haven't seen it before. Thank you. ip ssh version 2 vty 0 4 transport preferred ssh vty 5 15 transport input ssh transport input ssh
Hey all, I've been stumped on this issue for a while now. We implemented a VPN with our Cisco 1941 router with AnyConnect, but the speeds are far from functional: 350kbps to 1.7mbps. Sometimes the connection just dips out and a re-connect is needed. ...
We have a Cisco ISR 4321 with the Gigabitethernet0 (management) port in a seperate VRF (Mgmt-intf). It has been assigned an IPv6 address which cannot be reached until the router itself initiates a ping. The Mgmt-intf VRF has been setup with a defau...
Resolved! DHCP Issue on VRF
Hi Teck People i am facing on strang issue in my Distribution 9600 if some body face this issue guide me please IP phone is not getting IP Address from Cisco 96000 DHCP Server but Serve is showing the binding: DHCP SERVER Binding: Switch-1A#show ip...
HI allIn Cisco ISR G2 C2900 EOL Notice:https://www.cisco.com/c/en/us/products/collateral/routers/2900-series-integrated-services-routers-isr/eos-eol-notice-c51-737831.htmlRouters 2900 Series will be "for "End of SW maintenance release date : HW" by ...
