We have a site were Router WAN interface is configured with PPPoe - dial up. There is a requirement of publishing one application outside from same site. Is there any option to configured source static NAT pointing to dial-up WAN interface.
Forum Posts
Good afternoonI have Cisco 7606 as core(with directly connected multicast sources, configured as RP) and few 4900M connected in ring, and few l3 switches with customers connected to 4900. OSPF+PIM-SM.Multicast traffic working in all network, but on o...
hi all ; i need your help, advice. i have a topology that include 1 hq and 2 sites. i have 2 dmvpn tunnel. one is belongs to primary link of isp(tunnel 100), other one is belongs to backup link of isp(tunnel 200). tunnel 100 is running bgp, tunnel 2...
Hello All, I have two cisco 9200 switches connected back to back. the two switches were connected through an ether channel (2 ports on each switch) in active mode. We lost power to both switches and all the ports in the ether channel went into suspen...
Hi all, Possibly something simple that i'm missing but we've got an ISR4331 and it has 4 ethernet ports on it, there are 2 on the top of the 4 ports that are labelled ge0/0/0 across BOTH of them and then ge0/0/1 and ge0/0/2 underneath. I have 3 ports...
Hi,i tried enabling 'ip finger' command in my router, but it isnt' working, please helpRouter#config terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)#ip finger^ % Invalid input detected at '^' marker.
Hi All, Hopefully this can be done. I have tirelessly looked through the forums and tried to see if others can do the same and tried different configs but no go. Here is what I am trying to do.I have a USG Router with 2xWAN ports and 1xLAN port WAN1...
Hoping I am missing something simple here. I need to have a backup VPN connection work, but routing isn't propagating. My topology: I have three locations, A, B, and C. Site A is the main location and has an ASA and a 2921 routerSite B also as an ASA...
Hellowe have a project to create a network in Data Center to host a few servers and establish BGP connectivity with two different ISPs. Please see attached diagram company has public /24 networkwe have 3 routers : 2 Cores router connected to ISP and ...
Hello all, I have a simple topology where a Router(R1) has three interfaces g0/0 - 10.10.10.6 to other OSPF neighbor (area 0) (to R2 router)g0/1 - to /24 network (networkd in OSPF area 0) 172.28.6.0/24g0/2 - to /24 Network (networkd in OSPF area 0) 1...
Sir, I'm asking about host table configured in router. I studied that host table in router is an alternative for dns server. I configured host table in my router in packet tracer. The problem is i cannott ping pc to pc by name. But i can ping from ro...
I am still relatively new at this but could someone give me a hand with the ASR901 config? I can get a DHCP address from the ASR but still can get to the internet Current configuration : 4101 bytes!! Last configuration change at 21:17:54 PDT Fri Jun...
Hello for everybody. On one of the sites, we use router-on-a-stick technology. On this site, we decided to add one new network and allow access for pc from this network only to the same network and one another. Whether the correct solution is to do t...
Resolved! rv042g tunnel zyxel usg 200
Helloon me setup i have two company "A" with Cisco rv042g and company "B" Zyxel USG 220.this two are connected over tunnel (internet) with IPsec 3des and (1024bit group) configured,and this running... but! I have now missured the transfer speed that ...
Hi gentlemen,How can I decide type of VPN that is most appropriate to implement for a customer? DM VPN- GET VPN- FLEX VPNHow much each one cost for customer?Thanks alot
