Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
I have two routers connected with serial interfaces and to begin with I was unable to ping either router, anyway I want to configure OSPF 100 with the routers on area 0 the current configs are Router 1:Building configuration... Current configuration ...
Hi.. i am looking to upgrade ASR 1002, 2RU router from software ver. asr1000rp1-adventerprisek9.02.04.00.122-33.XND.bin to asr1000rp1-adventerprisek9.03.16.08.S.155-3.S8-ext.bin. Also running current Rommon ver 12.2(33r)XNC.Please confirm if i would...
Hello, I got a Cisco 1921 router, with 2 gigabit ports, and my ISP gives me a 1gbit/200mbit connection, so today I went for a speed test and I get the results between 90/90 and 280/200(after the Cisco 1921), My setup is the following-> ISP Router ->...
Hi, we have lan switches 9300 and mpls between them, everything is internal LAN. Does it make sense to add " auto qos trust dscp" on the connected interfaces btw those switches? As I read mpls does carry 3 bits of dscp into packet, but not sure do i ...
Hello community,I need to establish a L2 VPN over a L3 Network.The Goal is, to span an existing VLAN from a on PE Router to the other.The gateway of this VLAN is also the PE Router (no CE Router). See picture.I currently can only simulate it with GNS...
Hello, Can we terminate 2 different ISP (e.g. 10+10 Mbps) on one router to achieve 10 Mbps in load sharing/load balancing and high availability both ? Option 1: - Internet connectivityOption 2: - Point to Point connectivity (leased link)
We are running iWAN 2.2, PfR v3. We're running into odd load-balancing issues. With the standard configuration of ...!domain TEST vrf EXAMPLE master hub load-balance!...is it true that only uncontrolled traffic is load-balanced? If ...
Hello All,There seems to be an issue when pinging between our HQ (*Site A - Firepower VM) and remote site (*Site B - SFR Module on ASA). Pinging is fine when using the default byte size. But, when pinging with, for example 500 bytes or larger, there'...
Hello everyone,I am trying to figure out the use cases for iBGP vs eBGP. I understand the differences between the two but I am having a hard time figuring out in what scenario would you use iBGP vs eBGP.Thanks everyone in advance !!! I appreciate any...
I have a test Network that I'm using for my certifications. I have an1841 router and a 2811 router. I have the two routers connected with a WAN connection using a smart serial cable. I am using a WIC2T card in both routers. I noticed the connection ...
In short CPU load isn't very high nor is memory usage. Netflow metrics don't indicate anything unusual but we every once in awhile we run into a weird issue where it seems like we are running into a bandwidth limitation on the system where we should...
Hello everyone,I have a RV340 version 1.0.02.16 (new firmware) and I am trying to create a L2TP / IPSec vpn for Windows 7 and Android 8.0 clients.In Android, the vpn was created and disconnected as quickly. Under windows I always have a 789 error.I t...
Please let me know the routing to establish the communication to the cloud .Condition:It should not expose to the LAN.Note:1.Server 1 Has 2 NIC 1 is connected to LAN and NIC 2 is connected to Isolated Network which 10.0.10.0/24 Accomplished :1.Iso...
Hi all,Sorry if this is the wrong place for this question. Im new to stackoverflow.I'm trying to follow a guide for HA on azure but im falling at the first hurdle.The youtube video links are expired so i had to fill the gaps on the config and may hav...
Is it possible to setup a BGP peer using the HSRP virtual address as neighbour and source IP ?
.jpg "Hall of Fame Master"){kind=icon}
.jpg "VIP Collaborator"){kind=icon}
