VMX1(L2/L1) <------->eth0 R1 (L1/L2) eth0/1 <-------> eth0/1 R3 (L1) R1 is a l1/l2 router. In my understanding, its outbounding L1 LSP should have attached bit turned on. I captured the packets on its interface e0/1 to get the following.R1#show int...
Hi Gurus,I have a connection to ISP_A(int G0/1) and another connection to ISP_B (int G0/2) they all terminated at my router. With interface G0/0 as my internal interface.I have routed traffic from my servers farm (10.10.5.0/24) through ISP_A and my ...
hi everybody,i've issue with netflow statistics for nat translation, somehow in netflow statistics on collector appear tthe start of unix time 1970-01-01 04:00:00.000. although the time on asr is configured correctly:sh clock detail 10:18:02.508 MSK ...
We have a Cisco 819-4G Router which is used for downloading content to screens on a boat. It has worked well for the last few years but within the last week, it has failed to download anything.I have trouble-shooted today by double-checking the confi...
Hi All, Can you pls explain the functional difference between VSS and Stackwise Virtual.If both are same then why cisco introduced stackwise virtual
Hi, I am currently learning about DHCP and would like to know more.I have the set up shown in the image with Router0 being the DHCP in this case. I have got PC4 and 5 in the same VLAN and there is a trunk from Switch1 to Switch2, likewise from Switch...
Hello! Apologies in advance if this question doesn't make sense as I am just starting to learn eBGP Multihop.My topology is : R14 <---> R13 <----> R6 /// Where R6 and R14 are established and exchanging their loopbacks.I believe I have the configurat...
dear all how can i change the password and username for the following devices : - WS-C3850-48F-S (CORE SWITCH)- ASA5516-FTD-K9 (ASA FW)- C1-AIR-CT3504-K9 (WLC)
I am very new to routing and have zero background in it. My situation is that I have a Cisco 2811 router and wanted for my serial console cable to connect to the TFTP server and auto-configure. All I have connected is the RJ45 (2811/DTE end) to USB ...
I have two cisco routers, one newer 2811 connecting to an older 2600 in the following setup, internet ----- fibre modem --- 2600 ---- 2811 ---- internal network the 2600 is being used as a router/firewall on the internet and has an IP address conne...
Hi all. I have tried to do some bridging on a ASR1001-X with no luck so far. I have done this may times before on ISR-G2 routers with great success, but now I have to do it on a ASR1001-X router. The setup consist in simple terms of a ASR1001-X r...
Hi, I've got an interesting problem I'm trying to fix. We have some software which needs to contact a remote license server, it attempts to do this by sending a subnet broadcast to UDP-1947. On the 4500 VSS switch we have the following things configu...
Hello, Just looking for a little advise. Basiclly we have a router with two circuits on it. The idea is that when one fails it will push over to the other and vice versa. We already have tracking in place for some routes on a circuit, but they want ...
I cannot ping LAN networks behind R1 from PE-1. Even though they are in PE-1 routing table. From R1 I am able to ping LAN networks. SWC I have redistribute EIGRP and BGP. My traceroute from PE-1 towards to LAN network stops on R1. R1 and SWC are runn...
Hi everyoneI am beginner on this forum ...I see that ISR4321 has 2 power supply possibilities as written on the connector.My question is that can I power it from the existing rack with 48V instead with the delivered 12V power supply?If yes somebody ...
