Dear all, I would just like to quick confirm.So specific IOS-XE version on ISR4K, it can support for "ip nat enable" command on ISR4K interface configuration mode however I think NVI interface does not function because no link up so I think it still ...
Forum Posts
Resolved! Unable to shift the traffic using EIGRP
Hi, Can anyone help me with this topology. (Topology attached) I want to shift the traffic using EIGRP protocol. My destination in 10.68.96.0/30 network. Currently the traffic is preferring from R5 via R3,R2 and R1. but i want to shift the traffic v...
Hi Guys, does anyone know the problem that after a migration of RP2 from 3.x to 16.x the SIP10 cards are no longer recognized?And yeah, I know that the SIP10 with 16.x are no longer supported, but the cards are not recognized anymore in other routers...
I am currently testing PFRv3 in lab environment.I have tried to make single HUB-MC with two other routers as MC-Borders. on the Spoke side Branch MC and Border are on the same router. However, the PFRv3 channels cannot go both to RX state:From DMVPN ...
Resolved! ME 3800X | Bridge Domain Limit
We have setup where we are using a bridge-domain interface to connect to different CPEs through our ME3800. The BDI is setup on say BDI3 and we receive on different ports with different encapsulations/vlans, then strip the incoming tags off and place...
Resolved! 3925 basic config
I am trying to get this thing to have internet from GE0/0 available in the LAN connected to GE0/2 and am probably missing something stupid. I am able to ping google from the router but not from a computer on the LAN. version 15.2service configservice...
Router>sh ipv6 ospf n Neighbor ID Pri State Dead Time Interface ID Interface172.16.10.5 1 FULL/DR 00:00:36 2 FastEthernet0/0 What does 'Interface ID' mean???
I have 2 Branches connecting to same BGP Network with rest of Branches and HQ, I would like have fail over between these 2 Branches which are also connected P2P over WiMax Link , If obe Branch 1 Wan Fails I would all Traffic to go using Branch 2 Wan ...
Resolved! BGP Backdoor MPLS
helloi have below scenarioP router includes : R1 , R2 , R3 , R4PE router includes : R5 , R55 , R12 , R13CE router includes : R6 , R7 , R10 , R112 GREEN circle indicates 2 prefixes suppose : 1.1.1.0/24 & 2.2.2.0/24we have MPLS core backbone but for t...
Resolved! QoS packet drops
We have a 3945 router which is connected to our Service Provider's MPLS Cloud. There is a 100Mb circuit being delivered via Ethernet and is terminated on the Gi0/0 interface. We have the interface configured for 100Mb/full duplex. There is also Q...
There are two Cisco Routers in a Remote Branch & Border Gateway Protocol is running on both the Router & their inside interfaces are connected to a LAN Layer 3 switch enabled with Hot Standby Router Protocol.both the Router's outside interfaces are ...
hi everybodyi have router 3925 with IOS version c3900-universalk9-mz.SPA.156-3.M4.binTechnology Package License Information for Module:'c3900' ------------------------------------------------------------------------ Technology Technology-package ...
First of all I have four stack and I noticed the same problem with all of them when I’m adding a new member to stack. The scenario of action is as below. 1. There is stack with for example 5 members.2. Adding a new member with the same software versi...
Resolved! iBGP path manipulation
Hi Networkers,One of my clients requires Internet conductivity for 2 of the sites which are interconnected using L2 link. Client is very specific about the requirements. I have attached the Diagram for more understanding of the current infrastructure...
We have a client where we have to replace a router ( Cisco 1921 Series) which had failed. We had to replace it wit Cisco 841M router since 1900 series is end of sale. As the earlier router had failed, we do not have any information about configurati...
