Hi,I am in the process of deploying a new network scenario as per the design outlined in the attached design document (design.png).Additionally, I have prepared a BGP configuration file (bgp configuration.docx) according to the diagram that I would l...
Forum Posts
Resolved! IR9300 Issue on extended access-list
Hello, I have the below access-list that when working I have Internet connectivity on 10.252.92.1 host, but when I move 21 below the deny commands I cannot, it is like it is rejecting the permit. Could anyone help me why? To me it seems like a bug bu...
Here is a bit of a complex issue I need assistance finding the answer to. We're directly connected to another office that more or less manages their own network. The handoff between their network and ours is our equipment. They have their own Interne...
I have a situation in a lab topology and I can't seem to figure out how things work: So redistribution is configured between OSPF process 1 and 2 on both R1 and R2. Filtering using route tags is in place in such a way that no network will be redistr...
Hello, everyone! I'm operating a Cisco ISR 4331 Router loaded with IOS 17.06.06a and ROMMON 17.6.2. To get to the latest and greatest, I'd like to upgrade to IOS 17.12.3a. However, I read in another topic concerning upgrade procedures that going stra...
Hello Guys,We are planning to upgrade Cisco router Cisco C8300-1N1S-4T2X from XE image 17.6.5 (Rommon image 17.3(5r)) to latest XE image 17.9.5a. As per Rommon compatibility matrix, this new XE image should have minimum rommon image of 17.3(1r) and m...
I am setting up a C1111-8PWA-WS for the first time. After not being able access the internal wireless card I decided to set up without it. I have a Cisco SG350-28P switch that has POE for the AP's. Trying to set up the basic unit with just the rou...
Hello all,When I create a VRF on a router or L3 switch, am I creating just a separate routing table (like just a separate dictionary of routes), or am I creating an actual new routing process on the box ? So often in diagrams I will see VRF's represe...
Resolved! Routuing
Hello every one i want configure this three router, every router in different subnet, how i achieve connectivity. thank in advance i know one solution VRF but i don't need currently use vrf, i want only connectivity config from R2interface GigabitEth...
I am currently trying to set an alarm for collisions in multiple routers throughout our company and they are asking for the OID for collisions. Im not to sure how to answer so am looking for some guidance. Thank you
I went thru and added the followingexisting eigrp:router eigrp 99network 10.76.0.0 0.0.0.255network 10.76.2.0 0.0.0.255network 10.76.10.0 0.0.0.255network 10.76.200.0 0.0.0.255network 172.16.0.0network 192.168.10.0redistribute ospf 99 metric 10000 10...
flow record NETFLOW-RECORD-INmatch ipv4 protocolmatch ipv4 source addressmatch ipv4 destination addressmatch interface inputmatch flow directioncollect transport tcp flagscollect counter bytes longcollect counter packets longcollect timestamp absolut...
Resolved! Cisco 2960 switch NAT
Hi all, I have a Cisco 2960 switch running IOS 15.2(7) E7. I configured NAT overload.Straight forward config:interface Vlan150description INSIDE-LANip address 10.150.0.254 255.255.255.0ip nat inside!interface Vlan192description OUTSIDE-LANip address ...
Hi All,We are redesigning the Management of of offices network devices.network is like belowVlan 300-----SW--10.1.1.1----------10.1.1.2 Router----WANwe will configure reverse static router for 192.168.1.0/24 in router.Option 1- User separate manageme...
Resolved! Trunk Port Switch to Switch
On a switch-to-switch interface, can we configure both of these commands at the same time, or can we only configure one of them?switchport mode trunkswitchport trunk allowed vlan allinterface GigabitEthernet1/1/3description ****Uplink-Block-Switchswi...
