cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1488
Views
4
Helpful
9
Replies

Cisco 1841 hang

kchatila75
Beginner
Beginner

I got a new cisco 1841 recently. Everything went fine during configuration then suddenly I got the following:

libavas#

*Feb 21 10:52:47.043: %FILESYS-5-CF: External CompactFlash removed

System Bootstrap, Version 12.4(13r)T8, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2008 by cisco Systems, Inc.

PLD version 0x10

GIO ASIC version 0x127

c1841 platform with 196608 Kbytes of main memory

Main memory is configured to 64 bit mode with parity disabled

Upgrade ROMMON initialized

boot: cannot open "flash:"

boot: cannot determine first executable file name on device "flash:"

System Bootstrap, Version 12.4(13r)T8, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2008 by cisco Systems, Inc.

Both copies of nv_flash are corrupted

Warning: monitor nvram area is corrupt ... using default values

Warning: Because of corrupted monitor nvram, falling to Readonly ROMMON

System Bootstrap, Version 12.4(13r)T9, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2008 by cisco Systems, Inc.

PLD version 0x10

GIO ASIC version 0x127

c1841 platform with 196608 Kbytes of main memory

Main memory is configured to 64 bit mode with parity disabled

Readonly ROMMON initialized

rommon 1 >

rommon 1 >

rommon 1 >

rommon 1 > reset

After that, I'm not able to access the router, it got hang everytime I booted the router as shown below:

System Bootstrap, Version 12.4(13r)T9, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2008 by cisco Systems, Inc.

PLD version 0x10

GIO ASIC version 0x127

c1841 platform with 196608 Kbytes of main memory

Main memory is configured to 64 bit mode with parity disabled

Readonly ROMMON initialized

program load complete, entry point: 0x8000f000, size: 0xcb80

program load complete, entry point: 0x8000f000, size: 0xcb80

program load complete, entry point: 0x8000f000, size: 0xf64f68

Self decompressing the image : ############################################################################################################################################################ [OK]

Smart Init is enabled

smart init is sizing iomem

ID MEMORY_REQ TYPE

0X003AA110 public buffer pools

0X00211000 public particle pools

0X04C8 0X00077D00 Card in slot 0

0X000021B8 Onboard USB

If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Allocating additional 13997651 bytes to IO Memory.

PMem allocated: 178257920 bytes; IOMem allocated: 23068672 bytes

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, 1841 Software (C1841-BROADBAND-M), Version 12.4(4)T8, RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Fri 10-Aug-07 14:54 by khuie

Image text-base: 0x6008B840, data-base: 0x615888E0

I'm stuck, Please advice.

9 REPLIES 9

paolo bevilacqua
Hall of Fame Master Hall of Fame Master
Hall of Fame Master

In rommon, try 'sync' and copy the image again using tftpdnld. If still fail,it's HW fault and you need to return the unit via RMA.

I tried sync, and i used different CF with a new image, but same symptoms. Does it mean HW issue :(

Do you still have the nv errors at boot? Can you use tftpdnd to copy the image ?

My issue is that I'm not getting any single error/warning during bootup. It reach a level just before prompt & hang there. Previously, I have attached the level I'm reaching with bootup.

I tired tftpdnd before but I was getting illegal MAC Address. That's why I tried different CF to avoid image corruption.

In the first message you posted, there are nv errors during boot. I was asking if you still had these.

The illegal MAC points to something very wrong. Possibly, you should be able to get more information from rommon.

All in all, unless you want to spend more time troubleshooting this, I would have the unit replaced.

Thx, I'll go for RMA

Leo Laohoo
VIP Community Legend VIP Community Legend
VIP Community Legend

Weird. It seems, in my guess, someone tried unsuccessfully to upgrade the bootstrap.

System Bootstrap, Version 12.4(13r)T8, RELEASE SOFTWARE (fc1) < --- Bootstrap ver 12.4(13r)T8

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 2008 by cisco Systems, Inc.

Both copies of nv_flash are corrupted

Warning: monitor nvram area is corrupt ... using default values

Warning: Because of corrupted monitor nvram, falling to Readonly ROMMON

System Bootstrap, Version 12.4(13r)T9, RELEASE SOFTWARE (fc1) < --- Bootstrap ver 12.4(13r)T9

Where did you get the router? Bootstrap version 12.4(13r)T8 and T9 are not available. The "latest" is 12.4(13r)T5 (release date 06/Oct/2008).

I recommend you try to "downgrade" the bootstrap and see if this works.

Routers > Cisco 1841 Integrated Services Router > IOS ROMMON Software >

Hope this solves your problem.

Hmmm... it could be that it shipped like that from factory although rommon is not released yet on CCO.

Perhaps they introduced a newer HW revision.

Hi Paolo,

Hope I'm wrong. 6 months ago we took delivery of two ASR 1002 and both came with IOS that were NOT to be released to the general public. And I've about bootlegged audio files shipped out on official Cisco CD's.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: