cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Community Helping Community

406
Views
0
Helpful
11
Replies

Cisco 2600 Access Point with Trunk link to Cisco 3750-G

I wanted to configure trunk link between AP and Cisco Switch. When i make the link trunk then I am not able to ping the Switch. 

Can someone help me configuring Access Point.

We have only 1 vlan i.e. 300 and want to configure SSID for this VLAN on Cisco 2600 Access point.AP, Cisco, Erro

 

 

Thanks & Regards, 

Hamid Sattar

11 REPLIES 11

Re: Cisco 2600 Access Point with Trunk link to Cisco 3750-G

I am using this guide to configure it. But it's not working. Here is the link to guide.
https://www.cisco.com/c/en/us/support/docs/wireless-mobility/service-set-identifier-ssid/116118-configure-ap-ssid-ios.html
VIP Advisor

Re: Cisco 2600 Access Point with Trunk link to Cisco 3750-G

Hope you looking to have Autonomous AP with a single device? If yes try

 

Below Steps help you :

 

1. Do you have Right IOS image to configure Autonomous AP?

2. Connect the console cable to AP

3. Reset to Factory Default AP

4.  connect the laptop with IP address 10.0.0.10 (configured)

5. configure the AP

 

 with IP address example : 10.0.0.1 255.255.255.0

no shutdown

 

  • Test the connection by pinging: ping 10.0.0.10
  • Upload the image from the TFTP server of your laptop to the AP:
  •  archive download-sw /force-reload /overwrite tftp://10.0.0.10/image.tar

Follow below Guide :

 

https://www.cisco.com/c/en/us/td/docs/wireless/access_point/15-3-3/configuration/guide/cg15-3-3/cg15-3-3-chap4-first.html

BB
*** Rate All Helpful Responses ***
VIP Mentor

Re: Cisco 2600 Access Point with Trunk link to Cisco 3750-G

Hi,

 

First check whcih image you have:

 

  • k9w7 - autonomous (or "site survey") IOS 
  • k9w8 - full lightweight IOS/AP-COS (this is what is bundled in the WLC .aes image, and is factory installed on "mesh" APs)

Normally....

Local mode AP must be connected to access ports.

Autonomous mode AP must be connected to trunk port.

 

 

Regards

Dont forget to rate helpful posts

Re: Cisco 2600 Access Point with Trunk link to Cisco 3750-G

I am using this IOS image
Cisco IOS Software, C2600 Software (AP3G2-K9W7-M), Version 15.2(4)JB6, RELEASE SOFTWARE (fc1)

Re: Cisco 2600 Access Point with Trunk link to Cisco 3750-G

When I configure Trunk link on switch I am not able to ping it. Everything works fine if I don't make that link as Trunk Link.
Highlighted
VIP Mentor

Re: Cisco 2600 Access Point with Trunk link to Cisco 3750-G

is there any specific reason, why you want to configure it as trunk port ?

Re: Cisco 2600 Access Point with Trunk link to Cisco 3750-G

No. But I want to test it and configure it.
VIP Mentor

Re: Cisco 2600 Access Point with Trunk link to Cisco 3750-G

first check it has leighweight image or autonomous ?

Re: Cisco 2600 Access Point with Trunk link to Cisco 3750-G

Cisco IOS Software, C2600 Software (AP3G2-K9W7-M), Version 15.2(4)JB6, RELEASE SOFTWARE (fc1)
I think its Autonomous based

Re: Cisco 2600 Access Point with Trunk link to Cisco 3750-G

Interface IP-Address OK? Method Status Protocol
BVI1 192.168.32.47 YES NVRAM up up
Dot11Radio0 unassigned YES NVRAM administratively down down
Dot11Radio1 unassigned YES NVRAM administratively down down
GigabitEthernet0 unassigned YES NVRAM up up

As you can see I have above interfaces. Dot11Radio0 is for 2.4GHz and Dot11Radio1 is for 5Ghz.
Vlan in our Netork: 300
Native Vlan: 1

Can someone post configurations so that I can make trunk link between Access Point and Switchport.
VIP Mentor

Re: Cisco 2600 Access Point with Trunk link to Cisco 3750-G

CreatePlease to create content
Content for Community-Ad
FusionCharts will render here