cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
518
Views
0
Helpful
1
Replies

Cisco 2610 terminal server(no async ports)

wayne_fan
Beginner
Beginner

I got a terminal server with 2 octal cables attached to it. each octal cable has 8 RJ45 plugs. I installed a patch panel today and plug them into the back of the patch panel. I'll use the front panel as Out of Band ports.

However I can't access other device from my terminal server. I used rollover cable between the patch panel and my device. I was thinking maybe the octal cable is already rolled over. here are my partial output.

line 33 48

session-timeout 5

exec-timeout 5 0

flush-at-activation

no exec

transport input all

transport output none

escape-character BREAK

telnet ip-on-break

stopbits 1

flowcontrol hardware

AS05#sh line

Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int

0 CTY - - - - - 0 0 0/0 -

* 33 TTY 9600/9600 - - - - - 1 0 0/0 -

* 34 TTY 9600/9600 - - - - - 1 0 0/0 -

35 TTY 9600/9600 - - - - - 0 0 0/0 -

36 TTY 9600/9600 - - - - - 0 0 0/0 -

37 TTY 9600/9600 - - - - - 0 0 0/0 -

38 TTY 9600/9600 - - - - - 0 0 0/0 -

39 TTY 9600/9600 - - - - - 0 0 0/0 -

40 TTY 9600/9600 - - - - - 0 0 0/0 -

41 TTY 9600/9600 - - - - - 0 0 0/0 -

42 TTY 9600/9600 - - - - - 0 0 0/0 -

43 TTY 9600/9600 - - - - - 0 0 0/0 -

44 TTY 9600/9600 - - - - - 0 0 0/0 -

45 TTY 9600/9600 - - - - - 0 0 0/0 -

46 TTY 9600/9600 - - - - - 0 0 0/0 -

47 TTY 9600/9600 - - - - - 0 0 0/0 -

* 48 TTY 9600/9600 - - - - - 1 0 0/0 -

65 AUX 9600/9600 - - - - - 2 0 0/0 -

* 66 VTY - - - - - 7 0 0/0 -

67 VTY - - - - - 4 0 0/0 -

68 VTY - - - - - 0 0 0/0 -

69 VTY - - - - - 0 0 0/0 -

70 VTY - - - - - 0 0 0/0 -

Line(s) not in async mode -or- with no hardware support:

1-32, 49-64

1 ACCEPTED SOLUTION

Accepted Solutions

royalblues
Advocate
Advocate

The octal cables are already rolled over. you need to use a normal patch cable fron ur patch panel to the device

also configure

ip host R1 2033

ip host R2 2034

ip host R3 2035

ip host R4 2036

ip host R5 2037

ip host R6 2038

for all the lines

Narayan

View solution in original post

1 REPLY 1

royalblues
Advocate
Advocate

The octal cables are already rolled over. you need to use a normal patch cable fron ur patch panel to the device

also configure

ip host R1 2033

ip host R2 2034

ip host R3 2035

ip host R4 2036

ip host R5 2037

ip host R6 2038

for all the lines

Narayan

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: