Re: Cisco 2821 Router

saroj pradhan · ‎12-02-2011

Hi,

can some one provide me urgent support .

i have cisco 2821 router in my network and for the requiremet i have installed one dual port HWIC-2FE card .

in the show int and sh ip int br command it is not showing the newly installed FE but in the sh diag the following showing.

My Router has the version details below.

Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(11)XW9, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Sat 09-Aug-08 16:51 by prod_rel_team

ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)

WIC Slot 2:

2 Port FE HWIC

WIC module not supported/disabled in this slot

Hardware Revision : 2.0

Top Assy. Part Number : 800-33018-01

Part Number : 73-12949-01

Board Revision : A0

Deviation Number : 0

Fab Version : 03

PCB Serial Number : FOC15372RF7

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Product (FRU) Number : HWIC-2FE

Version Identifier : V02

CLEI Code : COUIAFUCAB

Base MAC Address : 7081.0575.845f

MAC Address block size : 2

Connector Type : 01

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 05 3B 41 02 00 C0 46 03 20 00 80 FA 01

0x10: 82 49 32 95 01 42 41 30 88 00 00 00 00 02 03 C1

0x20: 8B 46 4F 43 31 35 33 37 32 52 46 37 03 00 81 00

0x30: 00 00 00 04 00 CB 92 48 57 49 43 2D 32 46 45 20

0x40: 20 20 20 20 20 20 20 20 20 89 56 30 32 20 D9 02

0x50: 40 C1 C6 8A 43 4F 55 49 41 46 55 43 41 42 CF 06

0x60: 70 81 05 75 84 5F 43 00 02 05 01 FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

please advice to bring the interface UP.

Thanks,

Saroj

Mahesh Gohil · ‎12-02-2011

Hi,

sh diag output showing below error.

WIC module not supported/disabled in this slot.

So if it is supported on this platform kindly insert in another slot and check.

Regards # Mahesh

saroj pradhan · ‎12-02-2011

I have installed on another slot found same problem.

Can you please advice the Interface Module supported by cisco 2821 Router.

Thanks,

Saroj

Leo Laohoo · ‎12-03-2011

You've got the wrong IOS. You need an IOS with the "T" train.

saroj pradhan · ‎12-03-2011

if i upgrade the IOS of T will the interface work ?

Leo Laohoo · ‎12-03-2011

If you upgrade to an IOS with the "T" train, your interface will be detected by the router.

saroj pradhan · ‎12-03-2011

Can you please provide me the Exat ios ver.

Leo Laohoo · ‎12-03-2011

Can you please   provide me the Exat  ios ver.

Go to the Cisco Download site and look under the 12.4T category. Choose the IOS of your choice from this category.

saroj pradhan · ‎12-03-2011

OK Thanks….

saroj pradhan · ‎12-03-2011

Will it work for me ?

Release

12.4.24T6

Filename

c2800nm-adventerprisek9-mz.124-24.T6.bin

Product Code

S28NUAESK9-12424T

Release Date

31/Aug/2011

Minimum Memory

DRAM:256 MB Flash:128 MB

Size

58067.5859375 KB (59461208 bytes)

Router Checksum

0x2821

MD5

5ab04724ee2b6230872352f14e719f96

Additional Information

Security Advisories

Field Notices

stasinski_j · ‎12-03-2011

Yes it will, just make sure you have DRAM:256 MB Flash:128 MB on board and you can go ahead.

BR,

Jacek

saroj pradhan · ‎12-03-2011

Thanks for the support I will use another IOS as my Router has 64 mb.

The IOS I Will use ---c2800nm-advsecurityk9-mz.124-24.T6.bin which is 36MB.

But my Router has free space only 5775360 bytes available so how to upgrade ?

stasinski_j · ‎12-03-2011

simply type "yes" when you see prompt:

"Erase flash: before copying? [confirm]" y

It will erase flash and make space for new IOS.

http://www.cisco.com/en/US/products/ps5855/products_tech_note09186a00801fc986.shtml#example1

BR,

Jacek

saroj pradhan · ‎12-03-2011

I don’t get the option Erase Flash :before Copying .

Get the Error : %Error copying ftp://****:****@122.168.191.87/c2800nm-advsecurityk9-mz.124-24.T6.bin (Not enough space on device)

Please advice other options…..

Richard Burts · ‎12-04-2011

The other option is to manually delete the existing image from flash and then copy the new image into flash.

I have done this many times and it works. Note that there is a potential problem with doing this - if the router were to reload for some reason after you have manually deleted the existing image and before the download of the new image has completed then the router will not have an image to boot. This is not likely but you do need to be aware of the possibility in deciding whether you want to use this option.

HTH

Rick

HTH

Rick