02-01-2011 06:56 AM - edited 03-04-2019 11:16 AM
I am configuring a WAE-7341 for standalone content engine ACNS used for webcaching only.
When I enable the l2-redirect and l2-return on the WAE I get high CPU on my Cisco 6504-E with WS-SUP32-GE-3B - WS-F6K-PFC3B. The 6500 shows the wccp status as L2 for redirection and return and webcache works but this CPU spikes to 70%.
IOS Code: s3223-adventerprisek9_wan-mz.122-33.SXH7.bin
MDF-6504#show proc cpu sorted | exc 0.00
CPU utilization for five seconds: 47%/45%; one minute: 18%; five minutes: 27%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
152 9304 5144 1808 0.71% 0.22% 0.17% 1 SSH Process
139 46322920 12113823 3823 0.47% 0.40% 0.44% 0 CDP Protocol
I don't see which process is causing this but if I remove WCCP from the interface, it drops to 1% so I know for a fact that WCCP is causing this.
If I remove the l2-redirect and l2-return on the WAE, WCCP on the 6500 registers GRE for redirection and return on the 6500 and CPU drops to 5%.
If I enable the "wccp webcache accelerated" option on the 6500, I cannot get WCCP up with or without the l2-return and l2-redirect options on the WAE, it displays:
001782: Jan 28 21:24:00.055: WCCP-EVNT:wccp_update_assignment_status: enter
001783: Jan 28 21:24:00.055: WCCP-EVNT:wccp_update_assignment_status: exit
001784: Jan 28 21:24:00.055: WCCP-EVNT:S00: Here_I_Am packet from [ip hidden] w/bad fwd method 00000001, was offered 00000002
001785: Jan 28 21:24:00.055: WCCP-EVNT:S00: Here_I_Am packet from [ip hidden] with incompatible capabilites
Can anyone advise on this issue, does this 6500 not have the hardware redirect/rewrite capability? My WAE is directly connected to the 6500 WS-X6548-GE-TX blade on the same vlan that I am doing a wccp redirect on.
interface g3/4
description WAE-7341
switchport access vlan 600
interface VLAN 600
ip wccp web-cache redirect in
Solved! Go to Solution.
02-01-2011 12:18 PM
Any method, ideally you don't place the WAE on the same incoming VLAN as the user(s).
02-01-2011 07:14 AM
ip wccp web-cache redirect in should be entered on the user facing VLAN, not on the VLAN facing the web caching engine.
Please refer to this article for Best Practices http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps708/white_paper_c11-629052.html
Regards,
Edison
02-01-2011 07:31 AM
This WAE is outside the firewall.
[inside - 10.0.0.0/8]:ASA FW:[outside - vlan 600]
default route on ASA is my VLAN 600 SVI on the 6500. On this SVI I have WCCP redirect IN. The WAE is also on Vlan 600.
Please advise.
02-01-2011 09:43 AM
You are redirecting every web content back to the WAE with such design. This is causing a loop.
The design must have WCCP redirect-in on user facing VLAN and all web related flows would be redirected to your WAE.
I don't clear understand your network topology. Can you provide some diagrams?
02-01-2011 10:27 AM
Thanks for the response Edison. Attached is a quick drawing of the topology.
Traffic enters the firewall, comes in on the 6500, the 6500 redirects to webcache.
Let me know if the loop occurs in this topology.
02-01-2011 11:09 AM
You need to create an exception for the WAE so any traffic coming from this device isn't redirected in.
The link I provided has that info.
02-01-2011 11:12 AM
I see what your saying but that only applies to layer 2 redirect/return? Not for GRE ?
02-01-2011 12:18 PM
Any method, ideally you don't place the WAE on the same incoming VLAN as the user(s).
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: