Re: Configuring VDSL on Cisco 897-VA K9

somehow00 · ‎01-24-2021

Hi.

I'm trying to setup Cisco 897-K9 for my VDSL internet connection with dynamic IP (if I will successful then I’ll order a /29 IP prefix).

I was checking different configurations but no of them work.

Some people say I need to put for interface ATM0:

interface ATM0

no ip address

no atm ilmi-keepalive

pvc 8/35

encapsulation aal5mux ppp dialer

pppoe-client dial-pool-number 1

Others that interface ATM0 should be with no config and shutdown.

Also same with subinterfaces:

1).

interface ATM0.3 point-to-point

description Netia

pvc 8/35

encapsulation aal5snap

pppoe-client dial-pool-number 3

2).

interface Ethernet0.101

encapsulation dot1Q 101

pppoe-client dial-pool-number 1

With route or wiuthout route (ip route 0.0.0.0 0.0.0.0 Dialer1)

I’m really confused. Anyone can tell me how to configure it properly to make it work? Maybe it's the fault of my Controller firmware or something else

Info from my ISP (NETIA) about my line:

VDSL line

VPI: 8

VCI: 35

Multiplexing: LLC

Encapsulation: PPPoE

(Cable with rj11)

Modem firmware: VA_A_39m_B_38h3_24h.bin

Router#show controller vdsl 0

Controller VDSL 0 is UP

Daemon Status: Up

XTU-R (DS) XTU-C (US)

Chip Vendor ID: 'BDCM' 'IFTN'

Chip Vendor Specific: 0x0000 0xB203

Chip Vendor Country: 0xB500 0xB500

Modem Vendor ID: 'CSCO' ' '

Modem Vendor Specific: 0x4602 0x0000

Modem Vendor Country: 0xB500 0x0000

Serial Number Near: FCZ201790ZL C897VA-K 15.7(3)M4a

Serial Number Far: 5502610891

Modem Version Near: 15.7(3)M4a

Modem Version Far: 0xb203

Modem Status: TC Sync (Showtime!)

DSL Config Mode: VDSL2

Trained Mode: G.993.2 (VDSL2) Profile 17a

TC Mode: PTM

Selftest Result: 0x00

DELT configuration: disabled

DELT state: not running

Full inits: 1

Failed full inits: 0

Short inits: 0

Failed short inits: 0

Firmware Source File Name

-------- ------ ----------

VDSL embedded VDSL_LINUX_DEV_01212008

Modem FW Version: 4.14L.04A

Modem PHY Version: A2pv6C039t.d24o_rc1

Trellis: ON ON

SRA: disabled disabled

SRA count: 0 0

Bit swap: enabled enabled

Bit swap count: 1 0

Line Attenuation: 23.9 dB 0.0 dB

Signal Attenuation: 0.0 dB 0.0 dB

Noise Margin: 9.2 dB 9.0 dB

Attainable Rate: 33566 kbits/s 5940 kbits/s

Actual Power: 13.2 dBm 7.6 dBm

Per Band Status: D1 D2 D3 U0 U1 U2 U3

Line Attenuation(dB): 18.4 45.8 71.1 8.5 36.9 56.5 N/A

Signal Attenuation(dB): 18.3 45.3 N/A 8.5 36.7 55.5 N/A

Noise Margin(dB): 9.2 9.3 N/A 9.4 9.0 9.0 N/A

Total FECC: 0 0

Total ES: 0 0

Total SES: 0 0

Total LOSS: 0 0

Total UAS: 38 38

Total LPRS: 0 0

Total LOFS: 0 0

Total LOLS: 0 0

DS Channel1 DS Channel0 US Channel1 US Channel0

Speed (kbps): 0 30547 0 5492

SRA Previous Speed: 0 0 0 0

Previous Speed: 0 0 0 0

Reed-Solomon EC: 0 0 0 0

CRC Errors: 0 0 0 0

Header Errors: 0 0 0 0

Interleave (ms): 0.00 8.00 0.00 8.00

Actual INP: 0.00 2.00 0.00 1.10

Training Log : Stopped

Training Log Filename : flash:vdsllog.bin

——————

marce1000 · ‎01-24-2021

- Here's a YouTube example video , you may find it informational or helpful :

https://www.youtube.com/watch?v=meLtRs_GEUE

M.

-- ' 'Good body every evening' ' this sentence was once spotted on a logo at the entrance of a Weight Watchers Club !

balaji.bandi · ‎01-24-2021

here is the standard config : ( test and advise, still an issue, post the complete config)

https://katystech.blog/2020/12/fttc-vdsl-on-a-cisco-897va/

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

somehow00 · ‎01-24-2021

Unfortunately, it's not working. I've skipped the configuration of passwords, ssh, and NAT.

Router#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)

Router#sh ip int brief

Interface IP-Address OK? Method Status Protocol

ATM0 unassigned YES unset administratively down down

BRI0 unassigned YES unset administratively down down

BRI0:1 unassigned YES unset administratively down down

BRI0:2 unassigned YES unset administratively down down

Dialer0 unassigned YES manual up up <— on the blog it’s <ext-IP-address> and IPCP under Method

Ethernet0 unassigned YES unset administratively down down

Ethernet0.101 unassigned YES unset administratively down down

GigabitEthernet0 unassigned YES unset down down

GigabitEthernet1 unassigned YES unset down down

GigabitEthernet2 unassigned YES unset down down

GigabitEthernet3 unassigned YES unset down down

GigabitEthernet4 unassigned YES unset down down

GigabitEthernet5 unassigned YES unset down down

GigabitEthernet6 unassigned YES unset down down

GigabitEthernet7 unassigned YES unset down down

GigabitEthernet8 unassigned YES unset administratively down down

Virtual-Access1 unassigned YES unset up up

Vlan1 192.168.1.254 YES manual down down

It's my complete running-config (I only changed 192.168.1.254/24 to make it work with my current network devices):

Current configuration : 2490 bytes

!

! Last configuration change at 13:42:26 UTC Sun Jan 24 2021

!

version 15.7

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname Router

!

boot-start-marker

boot-end-marker

!

no aaa new-model

!

ip dhcp excluded-address 192.168.1.1 192.168.1.99

ip dhcp excluded-address 192.168.1.200 192.168.1.254

!

ip dhcp pool LAN

network 192.168.1.0 255.255.255.0

dns-server 9.9.9.9

default-router 192.168.1.254

!

ip cef

no ipv6 cef

!

multilink bundle-name authenticated

!

license udi pid C897VA-K9 sn FCZ201790ZL

!

redundancy

!

controller VDSL 0

!

interface ATM0

no ip address

shutdown

no atm ilmi-keepalive

!

interface BRI0

no ip address

encapsulation hdlc

shutdown

isdn termination multidrop

!

interface Ethernet0

no ip address

shutdown

!

interface Ethernet0.101

description PPPoE VLAN101

encapsulation dot1Q 101

no ip redirects

no ip proxy-arp

ip virtual-reassembly in

pppoe enable group global

pppoe-client dial-pool-number 1

!

interface GigabitEthernet0

no ip address

!

interface GigabitEthernet1

no ip address

!

interface GigabitEthernet2

no ip address

!

interface GigabitEthernet3

no ip address

!

interface GigabitEthernet4

no ip address

!

interface GigabitEthernet5

no ip address

!

interface GigabitEthernet6

no ip address

!

interface GigabitEthernet7

no ip address

!

interface GigabitEthernet8

no ip address

shutdown

duplex auto

speed auto

!

interface Vlan1

ip address 192.168.1.254 255.255.255.0

ip virtual-reassembly in

!

interface Dialer0

mtu 1492

ip address negotiated

no ip redirects

no ip unreachables

no ip proxy-arp

ip virtual-reassembly in

encapsulation ppp

ip tcp adjust-mss 1452

dialer pool 1

dialer-group 1

ppp authentication pap chap ms-chap callin

ppp chap hostname xxxxxx@xxxxxx.xx

ppp chap password 0 xxxxxxx

ppp ipcp address accept

!

ip forward-protocol nd

no ip http server

no ip http secure-server

!

ip route 0.0.0.0 0.0.0.0 Dialer0

!

ip access-list standard LAN

permit 192.168.1.0 0.0.0.255

!

ipv6 ioam timestamp

!

control-plane

!

mgcp behavior rsip-range tgcp-only

mgcp behavior comedia-role none

mgcp behavior comedia-check-media-src disable

mgcp behavior comedia-sdp-force disable

!

mgcp profile default

!

line con 0

no modem enable

line aux 0

line vty 0 4

login

transport input none

!

scheduler allocate 20000 1000

!

end

balaji.bandi · ‎01-24-2021

i prefer to see full current running-config removing any passwords. the main part NAT config which required.

also, post-show ip interface brief

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

somehow00 · ‎01-24-2021

I've already posted show ip interface brief - it's on the top of my last replay.

Sorry, I meant that I didn't type on the console configuration for hostname, user/password access, ssh, and NAT. I've shown my full running-config. If It's necessary to launch NAT to make vdsl connection to work , here it is:

Current configuration : 2645 bytes

!

! Last configuration change at 14:39:38 UTC Sun Jan 24 2021

!

version 15.7

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname Router

!

boot-start-marker

boot-end-marker

!

no aaa new-model

!

ip dhcp excluded-address 192.168.1.1 192.168.1.99

ip dhcp excluded-address 192.168.1.200 192.168.1.254

!

ip dhcp pool LAN

network 192.168.1.0 255.255.255.0

dns-server 9.9.9.9

default-router 192.168.1.254

!

no ip cef

no ipv6 cef

!

multilink bundle-name authenticated

!

license udi pid C897VA-K9 sn FCZ201790ZL

!

redundancy

!

controller VDSL 0

!

interface ATM0

no ip address

shutdown

no atm ilmi-keepalive

!

interface BRI0

no ip address

encapsulation hdlc

shutdown

isdn termination multidrop

!

interface Ethernet0

no ip address

shutdown

!

interface Ethernet0.101

description PPPoE VLAN101

encapsulation dot1Q 101

no ip redirects

no ip proxy-arp

ip virtual-reassembly in

pppoe enable group global

pppoe-client dial-pool-number 1

!

interface GigabitEthernet0

no ip address

!

interface GigabitEthernet1

no ip address

!

interface GigabitEthernet2

no ip address

!

interface GigabitEthernet3

no ip address

!

interface GigabitEthernet4

no ip address

!

interface GigabitEthernet5

no ip address

!

interface GigabitEthernet6

no ip address

!

interface GigabitEthernet7

no ip address

!

interface GigabitEthernet8

no ip address

shutdown

duplex auto

speed auto

!

interface Vlan1

ip address 192.168.1.254 255.255.255.0

ip nat inside

ip virtual-reassembly in

!

interface Dialer0

mtu 1492

ip address negotiated

no ip redirects

no ip unreachables

no ip proxy-arp

ip nat outside

ip virtual-reassembly in

encapsulation ppp

ip tcp adjust-mss 1452

dialer pool 1

dialer-group 1

ppp authentication pap chap ms-chap callin

ppp chap hostname xxx@xxxx.xx

ppp chap password 0 xxxxxx

ppp ipcp address accept

!

ip forward-protocol nd

no ip http server

no ip http secure-server

!

ip nat pool LAN 192.168.1.0 192.168.1.254 netmask 255.255.255.0

ip nat inside source list LAN interface Dialer0 overload <--- I have also tryed with: ip nat inside source list LAN interface Ethernet0.101 overload

ip route 0.0.0.0 0.0.0.0 Dialer0

!

ip access-list standard LAN

permit 192.168.1.0 0.0.0.255

!

ipv6 ioam timestamp

!

control-plane

!

mgcp behavior rsip-range tgcp-only

mgcp behavior comedia-role none

mgcp behavior comedia-check-media-src disable

mgcp behavior comedia-sdp-force disable

!

mgcp profile default

!

line con 0

no modem enable

line aux 0

line vty 0 4

login

transport input none

!

scheduler allocate 20000 1000

!

end

Georg Pauwen · ‎01-24-2021

Hello,

I think on the 897, the subinterface goes on interface GigabitEthernet8. Try the config below (important parts marked in bold

Current configuration : 2645 bytes
!
! Last configuration change at 14:39:38 UTC Sun Jan 24 2021
!
version 15.7
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
ip dhcp excluded-address 192.168.1.1 192.168.1.99
ip dhcp excluded-address 192.168.1.200 192.168.1.254
!
ip dhcp pool LAN
network 192.168.1.0 255.255.255.0
dns-server 9.9.9.9
default-router 192.168.1.254
!
--> ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
license udi pid C897VA-K9 sn FCZ201790ZL
!
redundancy
!
controller VDSL 0
!
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
!
interface BRI0
no ip address
encapsulation hdlc
shutdown
isdn termination multidrop
!
interface Ethernet0
no ip address
shutdown
!
interface Ethernet0
!
interface GigabitEthernet0
no ip address
!
interface GigabitEthernet1
no ip address
!
interface GigabitEthernet2
no ip address
!
interface GigabitEthernet3
no ip address
!
interface GigabitEthernet4
no ip address
!
interface GigabitEthernet5
no ip address
!
interface GigabitEthernet6
no ip address
!
interface GigabitEthernet7
no ip address
!
--> interface GigabitEthernet8.101
--> encapsulation dot1q 101
--> pppoe enable group-global
--> pppoe-client dial-pool-number 1
no ip address
duplex auto
speed auto
!
interface Vlan1
ip address 192.168.1.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface Dialer0
mtu 1492
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer-group 1
ppp authentication pap chap ms-chap callin
ppp chap hostname xxx@xxxx.xx
ppp chap password 0 xxxxxx
ppp ipcp address accept
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
--> ip nat inside source list 1 interface Dialer0 overload
!
--> ip route 0.0.0.0 0.0.0.0 Dialer0
!
--> access-list 1 permit 192.168.1.0 0.0.0.255
!
--> dialer-list 1 protocol ip permit
!
ipv6 ioam timestamp
!
control-plane
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
line con 0
no modem enable
line aux 0
line vty 0 4
login
transport input none
!
scheduler allocate 20000 1000
!
end

somehow00 · ‎01-24-2021

Heya,

Something has changed when show ip interface brief but still no ping to the internet, same from Compuyer behind the NAT.

Two commends didn't pass for interface GigabitEthernet8.101. I'd bold them.

Router# show ip interface brief

Interface IP-Address OK? Method Status Protocol

ATM0 unassigned YES NVRAM administratively down down

BRI0 unassigned YES NVRAM administratively down down

BRI0:1 unassigned YES unset administratively down down

BRI0:2 unassigned YES unset administratively down down

Dialer0 unassigned YES manual up up

Ethernet0 unassigned YES NVRAM administratively down down

GigabitEthernet0 unassigned YES unset down down

GigabitEthernet1 unassigned YES unset down down

GigabitEthernet2 unassigned YES unset down down

GigabitEthernet3 unassigned YES unset down down

GigabitEthernet4 unassigned YES unset down down

GigabitEthernet5 unassigned YES unset down down

GigabitEthernet6 unassigned YES unset down down

GigabitEthernet7 unassigned YES unset down down

GigabitEthernet8 unassigned YES NVRAM administratively down down

GigabitEthernet8.101 unassigned YES unset administratively down down

NVI0 unassigned YES unset up up

Virtual-Access1 unassigned YES unset up up

Vlan1 192.168.1.254 YES manual down down

Router#

Router#show run

Building configuration...

Current configuration : 2512 bytes

!

! Last configuration change at 18:12:16 UTC Sun Jan 24 2021

!

version 15.7

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname Router

!

boot-start-marker

boot-end-marker

!

no aaa new-model

!

ip dhcp excluded-address 192.168.1.1 192.168.1.99

ip dhcp excluded-address 192.168.1.200 192.168.1.254

!

ip dhcp pool LAN

network 192.168.1.0 255.255.255.0

dns-server 9.9.9.9

default-router 192.168.1.254

!

ip cef

no ipv6 cef

!

multilink bundle-name authenticated

!

license udi pid C897VA-K9 sn FCZ201790ZL

!

redundancy

!

controller VDSL 0

interface ATM0

no ip address

shutdown

no atm ilmi-keepalive

!

interface BRI0

no ip address

encapsulation hdlc

shutdown

isdn termination multidrop

!

interface Ethernet0

no ip address

shutdown

!

interface GigabitEthernet0

no ip address

!

interface GigabitEthernet1

no ip address

!

interface GigabitEthernet2

no ip address

!

interface GigabitEthernet3

no ip address

!

interface GigabitEthernet4

no ip address

!

interface GigabitEthernet5

no ip address

!

interface GigabitEthernet6

no ip address

!

interface GigabitEthernet7

no ip address

!

interface GigabitEthernet8

no ip address

shutdown

duplex auto

speed auto

!

interface GigabitEthernet8.101

encapsulation dot1Q 101

pppoe enable group global

pppoe-client dial-pool-number 1

<—- Router(config-subif)#duplex auto

<—- % Invalid input detected at '^' marker.

<—— Router(config-subif)#speed auto

<—— % Invalid input detected at '^' mark

!

interface Vlan1

ip address 192.168.1.254 255.255.255.0

ip nat inside

ip virtual-reassembly in

!

interface Dialer0

mtu 1492

ip address negotiated

no ip redirects

no ip unreachables

no ip proxy-arp

ip nat outside

ip virtual-reassembly in

encapsulation ppp

ip tcp adjust-mss 1452

dialer pool 1

dialer-group 1

ppp authentication pap chap ms-chap callin

ppp chap hostname xxx@xxx.xx

ppp chap password 0 xxxxx

ppp ipcp address accept

!

ip forward-protocol nd

no ip http server

no ip http secure-server

!

ip nat inside source list 1 interface Dialer0 overload

ip route 0.0.0.0 0.0.0.0 Dialer0

!

dialer-list 1 protocol ip permit

ipv6 ioam timestamp

!

access-list 1 permit 192.168.1.0 0.0.0.255

!

control-plane

!

mgcp behavior rsip-range tgcp-only

mgcp behavior comedia-role none

mgcp behavior comedia-check-media-src disable

mgcp behavior comedia-sdp-force disable

!

mgcp profile default

!

line con 0

no modem enable

line aux 0

line vty 0 4

login

transport input none

!

scheduler allocate 20000 1000

!

end

Georg Pauwen · ‎01-24-2021

Hello,

you need to 'no shut' interface GigabitEthernet8:

Router#conf t

Router(config)#interface GigabitEthernet8

Router(config-if)#no shut

somehow00 · ‎01-24-2021

Now in the config it's:

!

interface GigabitEthernet8

no ip address

duplex auto

speed auto

!

But anyway it's down:

Router#show ip interface brief
Interface IP-Address OK? Method Status Protocol
ATM0 unassigned YES NVRAM administratively down down
BRI0 unassigned YES NVRAM administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
Dialer0 unassigned YES NVRAM up up
Ethernet0 unassigned YES NVRAM administratively down down
GigabitEthernet0 unassigned YES unset down down
GigabitEthernet1 unassigned YES unset down down
GigabitEthernet2 unassigned YES unset down down
GigabitEthernet3 unassigned YES unset down down
GigabitEthernet4 unassigned YES unset down down
GigabitEthernet5 unassigned YES unset down down
GigabitEthernet6 unassigned YES unset down down
GigabitEthernet7 unassigned YES unset down down
GigabitEthernet8 unassigned YES NVRAM down down
GigabitEthernet8.101 unassigned YES unset down down
NVI0 unassigned YES unset up up
Virtual-Access1 unassigned YES unset up up
Vlan1 192.168.1.254 YES NVRAM down down
Router#

Georg Pauwen · ‎01-24-2021

Hello,

on which port is the ISP/cable modem connected ? Is that GigabitEthernet8 ?

somehow00 · ‎01-24-2021

it’s not connected from the ISP modem but straight from the line to “vdsl/adsl over POTS” Rj11 port.

Georg Pauwen · ‎01-24-2021

Hello,

try the ATM interface configuration marked in bold:

Current configuration : 2645 bytes
!
! Last configuration change at 14:39:38 UTC Sun Jan 24 2021
!
version 15.7
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
ip dhcp excluded-address 192.168.1.1 192.168.1.99
ip dhcp excluded-address 192.168.1.200 192.168.1.254
!
ip dhcp pool LAN
network 192.168.1.0 255.255.255.0
dns-server 9.9.9.9
default-router 192.168.1.254
!
--> ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
license udi pid C897VA-K9 sn FCZ201790ZL
!
redundancy
!
controller VDSL 0
!
interface ATM0
no ip address
--> ip nat outside
--> ip virtual-reassembly
no atm ilmi-keepalive
--> pvc 8/35
--> encapsulation aal5mux ppp dialer
--> dialer pool-member 1
!
--> dsl operating-mode auto
!
interface BRI0
no ip address
encapsulation hdlc
shutdown
isdn termination multidrop
!
interface Ethernet0
no ip address
shutdown
!
interface Ethernet0
!
interface GigabitEthernet0
no ip address
!
interface GigabitEthernet1
no ip address
!
interface GigabitEthernet2
no ip address
!
interface GigabitEthernet3
no ip address
!
interface GigabitEthernet4
no ip address
!
interface GigabitEthernet5
no ip address
!
interface GigabitEthernet6
no ip address
!
interface GigabitEthernet7
no ip address
!
interface GigabitEthernet8
no ip address
!
interface Vlan1
ip address 192.168.1.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface Dialer0
mtu 1492
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer-group 1
ppp authentication pap chap ms-chap callin
ppp chap hostname xxx@xxxx.xx
ppp chap password 0 xxxxxx
ppp ipcp address accept
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
--> ip nat inside source list 1 interface Dialer0 overload
!
--> ip route 0.0.0.0 0.0.0.0 Dialer0
!
--> access-list 1 permit 192.168.1.0 0.0.0.255
!
--> dialer-list 1 protocol ip permit
!
ipv6 ioam timestamp
!
control-plane
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
line con 0
no modem enable
line aux 0
line vty 0 4
login
transport input none
!
scheduler allocate 20000 1000
!
end

somehow00 · ‎01-25-2021

Hello,

Thank You for still having patience for this.

Router(config-if)#do show ip int brie

Interface IP-Address OK? Method Status Protocol

ATM0 unassigned YES NVRAM down down

BRI0 unassigned YES NVRAM administratively down down

BRI0:1 unassigned YES unset administratively down down

BRI0:2 unassigned YES unset administratively down down

Dialer0 unassigned YES NVRAM up up

Ethernet0 unassigned YES NVRAM administratively down down

GigabitEthernet0 unassigned YES unset down down

GigabitEthernet1 unassigned YES unset down down

GigabitEthernet2 unassigned YES unset down down

GigabitEthernet3 unassigned YES unset down down

GigabitEthernet4 unassigned YES unset down down

GigabitEthernet5 unassigned YES unset down down

GigabitEthernet6 unassigned YES unset down down

GigabitEthernet7 unassigned YES unset down down

GigabitEthernet8 unassigned YES NVRAM administratively down down

GigabitEthernet8.101 unassigned YES unset deleted down

NVI0 unassigned YES unset up up

Virtual-Access1 unassigned YES unset up up

Virtual-Access2 unassigned YES unset up up

Vlan1 192.168.1.254 YES NVRAM down down

Router(config-if)#

Here is runnning-config:

Building configuration...

Current configuration : 2436 bytes

!

version 15.7

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname Router

!

boot-start-marker

boot-end-marker

!

no aaa new-model

!

ip dhcp excluded-address 192.168.1.1 192.168.1.99

ip dhcp excluded-address 192.168.1.200 192.168.1.254

!

ip dhcp pool LAN

network 192.168.1.0 255.255.255.0

dns-server 9.9.9.9

default-router 192.168.1.254

!

ip cef

no ipv6 cef

!

multilink bundle-name authenticated

!

license udi pid C897VA-K9 sn FCZ201790ZL

!

redundancy

!

controller VDSL 0

!

interface ATM0

no ip address

ip nat outside

ip virtual-reassembly in

no atm ilmi-keepalive

pvc 8/35

encapsulation aal5mux ppp dialer

dialer pool-member 1

!

<—— Router(config-if)#dsl operating-mode auto

^

<—% Invalid input detected at '^' marker.

!

interface BRI0

no ip address

encapsulation hdlc

shutdown

isdn termination multidrop

!

interface Ethernet0

no ip address

shutdown

!

interface GigabitEthernet0

no ip address

!

interface GigabitEthernet1

no ip address

!

interface GigabitEthernet2

no ip address

!

interface GigabitEthernet3

no ip address

!

interface GigabitEthernet4

no ip address

!

interface GigabitEthernet5

no ip address

!

interface GigabitEthernet6

no ip address

!

interface GigabitEthernet7

no ip address

!

interface GigabitEthernet8

no ip address

shutdown

duplex auto

speed auto

!

interface Vlan1

ip address 192.168.1.254 255.255.255.0

ip nat inside

ip virtual-reassembly in

!

interface Dialer0

mtu 1492

ip address negotiated

no ip redirects

no ip unreachables

no ip proxy-arp

ip nat outside

ip virtual-reassembly in

encapsulation ppp

ip tcp adjust-mss 1452

dialer pool 1

dialer-group 1

ppp authentication pap chap ms-chap callin

ppp chap hostname jfthfojf@bn24.pl

ppp chap password 0 xxxxx

ppp ipcp address accept

!

ip forward-protocol nd

no ip http server

no ip http secure-server

!

ip nat inside source list 1 interface Dialer0 overload

ip route 0.0.0.0 0.0.0.0 Dialer0

!

dialer-list 1 protocol ip permit

ipv6 ioam timestamp

!

access-list 1 permit 192.168.1.0 0.0.0.255

!

control-plane

!

mgcp behavior rsip-range tgcp-only

mgcp behavior comedia-role none

mgcp behavior comedia-check-media-src disable

mgcp behavior comedia-sdp-force disable

!

mgcp profile default

!

line con 0

no modem enable

line aux 0

line vty 0 4

login

transport input none

!

scheduler allocate 20000 1000

!

end

Georg Pauwen · ‎01-25-2021

Hello,

we are missing something fundamental. What country are you in, and who is your ISP ?