01-24-2021 04:01 AM
Hi.
I'm trying to setup Cisco 897-K9 for my VDSL internet connection with dynamic IP (if I will successful then I’ll order a /29 IP prefix).
I was checking different configurations but no of them work.
Some people say I need to put for interface ATM0:
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5mux ppp dialer
pppoe-client dial-pool-number 1
Others that interface ATM0 should be with no config and shutdown.
Also same with subinterfaces:
1).
interface ATM0.3 point-to-point
description Netia
pvc 8/35
encapsulation aal5snap
pppoe-client dial-pool-number 3
2).
interface Ethernet0.101
encapsulation dot1Q 101
pppoe-client dial-pool-number 1
With route or wiuthout route (ip route 0.0.0.0 0.0.0.0 Dialer1)
I’m really confused. Anyone can tell me how to configure it properly to make it work? Maybe it's the fault of my Controller firmware or something else
Info from my ISP (NETIA) about my line:
VDSL line
VPI: 8
VCI: 35
Multiplexing: LLC
Encapsulation: PPPoE
(Cable with rj11)
Modem firmware: VA_A_39m_B_38h3_24h.bin
Router#show controller vdsl 0
Controller VDSL 0 is UP
Daemon Status: Up
XTU-R (DS) XTU-C (US)
Chip Vendor ID: 'BDCM' 'IFTN'
Chip Vendor Specific: 0x0000 0xB203
Chip Vendor Country: 0xB500 0xB500
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x4602 0x0000
Modem Vendor Country: 0xB500 0x0000
Serial Number Near: FCZ201790ZL C897VA-K 15.7(3)M4a
Serial Number Far: 5502610891
Modem Version Near: 15.7(3)M4a
Modem Version Far: 0xb203
Modem Status: TC Sync (Showtime!)
DSL Config Mode: VDSL2
Trained Mode: G.993.2 (VDSL2) Profile 17a
TC Mode: PTM
Selftest Result: 0x00
DELT configuration: disabled
DELT state: not running
Full inits: 1
Failed full inits: 0
Short inits: 0
Failed short inits: 0
Firmware Source File Name
-------- ------ ----------
VDSL embedded VDSL_LINUX_DEV_01212008
Modem FW Version: 4.14L.04A
Modem PHY Version: A2pv6C039t.d24o_rc1
Trellis: ON ON
SRA: disabled disabled
SRA count: 0 0
Bit swap: enabled enabled
Bit swap count: 1 0
Line Attenuation: 23.9 dB 0.0 dB
Signal Attenuation: 0.0 dB 0.0 dB
Noise Margin: 9.2 dB 9.0 dB
Attainable Rate: 33566 kbits/s 5940 kbits/s
Actual Power: 13.2 dBm 7.6 dBm
Per Band Status: D1 D2 D3 U0 U1 U2 U3
Line Attenuation(dB): 18.4 45.8 71.1 8.5 36.9 56.5 N/A
Signal Attenuation(dB): 18.3 45.3 N/A 8.5 36.7 55.5 N/A
Noise Margin(dB): 9.2 9.3 N/A 9.4 9.0 9.0 N/A
Total FECC: 0 0
Total ES: 0 0
Total SES: 0 0
Total LOSS: 0 0
Total UAS: 38 38
Total LPRS: 0 0
Total LOFS: 0 0
Total LOLS: 0 0
DS Channel1 DS Channel0 US Channel1 US Channel0
Speed (kbps): 0 30547 0 5492
SRA Previous Speed: 0 0 0 0
Previous Speed: 0 0 0 0
Reed-Solomon EC: 0 0 0 0
CRC Errors: 0 0 0 0
Header Errors: 0 0 0 0
Interleave (ms): 0.00 8.00 0.00 8.00
Actual INP: 0.00 2.00 0.00 1.10
Training Log : Stopped
Training Log Filename : flash:vdsllog.bin
——————
01-24-2021 05:06 AM
- Here's a YouTube example video , you may find it informational or helpful :
https://www.youtube.com/watch?v=meLtRs_GEUE
M.
01-24-2021 05:08 AM
here is the standard config : ( test and advise, still an issue, post the complete config)
https://katystech.blog/2020/12/fttc-vdsl-on-a-cisco-897va/
01-24-2021 06:16 AM
Unfortunately, it's not working. I've skipped the configuration of passwords, ssh, and NAT.
Router#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
Router#sh ip int brief
Interface IP-Address OK? Method Status Protocol
ATM0 unassigned YES unset administratively down down
BRI0 unassigned YES unset administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
Dialer0 unassigned YES manual up up <— on the blog it’s <ext-IP-address> and IPCP under Method
Ethernet0 unassigned YES unset administratively down down
Ethernet0.101 unassigned YES unset administratively down down
GigabitEthernet0 unassigned YES unset down down
GigabitEthernet1 unassigned YES unset down down
GigabitEthernet2 unassigned YES unset down down
GigabitEthernet3 unassigned YES unset down down
GigabitEthernet4 unassigned YES unset down down
GigabitEthernet5 unassigned YES unset down down
GigabitEthernet6 unassigned YES unset down down
GigabitEthernet7 unassigned YES unset down down
GigabitEthernet8 unassigned YES unset administratively down down
Virtual-Access1 unassigned YES unset up up
Vlan1 192.168.1.254 YES manual down down
It's my complete running-config (I only changed 192.168.1.254/24 to make it work with my current network devices):
Current configuration : 2490 bytes
!
! Last configuration change at 13:42:26 UTC Sun Jan 24 2021
!
version 15.7
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
!
!
ip dhcp excluded-address 192.168.1.1 192.168.1.99
ip dhcp excluded-address 192.168.1.200 192.168.1.254
!
ip dhcp pool LAN
network 192.168.1.0 255.255.255.0
dns-server 9.9.9.9
default-router 192.168.1.254
!
ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
!
license udi pid C897VA-K9 sn FCZ201790ZL
!
!
!
redundancy
!
!
!
controller VDSL 0
!
!
!
!
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
!
interface BRI0
no ip address
encapsulation hdlc
shutdown
isdn termination multidrop
!
interface Ethernet0
no ip address
shutdown
!
interface Ethernet0.101
description PPPoE VLAN101
encapsulation dot1Q 101
no ip redirects
no ip proxy-arp
ip virtual-reassembly in
pppoe enable group global
pppoe-client dial-pool-number 1
!
!
interface GigabitEthernet0
no ip address
!
interface GigabitEthernet1
no ip address
!
interface GigabitEthernet2
no ip address
!
interface GigabitEthernet3
no ip address
!
interface GigabitEthernet4
no ip address
!
interface GigabitEthernet5
no ip address
!
interface GigabitEthernet6
no ip address
!
interface GigabitEthernet7
no ip address
!
interface GigabitEthernet8
no ip address
shutdown
duplex auto
speed auto
!
interface Vlan1
ip address 192.168.1.254 255.255.255.0
ip virtual-reassembly in
!
interface Dialer0
mtu 1492
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer-group 1
ppp authentication pap chap ms-chap callin
ppp chap hostname xxxxxx@xxxxxx.xx
ppp chap password 0 xxxxxxx
ppp ipcp address accept
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
ip route 0.0.0.0 0.0.0.0 Dialer0
!
ip access-list standard LAN
permit 192.168.1.0 0.0.0.255
!
ipv6 ioam timestamp
!
control-plane
!
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
!
line con 0
no modem enable
line aux 0
line vty 0 4
login
transport input none
!
scheduler allocate 20000 1000
!
!
end
01-24-2021 06:31 AM
i prefer to see full current running-config removing any passwords. the main part NAT config which required.
also, post-show ip interface brief
01-24-2021 06:58 AM
I've already posted show ip interface brief - it's on the top of my last replay.
Sorry, I meant that I didn't type on the console configuration for hostname, user/password access, ssh, and NAT. I've shown my full running-config. If It's necessary to launch NAT to make vdsl connection to work , here it is:
Current configuration : 2645 bytes
!
! Last configuration change at 14:39:38 UTC Sun Jan 24 2021
!
version 15.7
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
!
ip dhcp excluded-address 192.168.1.1 192.168.1.99
ip dhcp excluded-address 192.168.1.200 192.168.1.254
!
ip dhcp pool LAN
network 192.168.1.0 255.255.255.0
dns-server 9.9.9.9
default-router 192.168.1.254
!
no ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
license udi pid C897VA-K9 sn FCZ201790ZL
!
redundancy
!
controller VDSL 0
!
!
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
!
interface BRI0
no ip address
encapsulation hdlc
shutdown
isdn termination multidrop
!
interface Ethernet0
no ip address
shutdown
!
interface Ethernet0.101
description PPPoE VLAN101
encapsulation dot1Q 101
no ip redirects
no ip proxy-arp
ip virtual-reassembly in
pppoe enable group global
pppoe-client dial-pool-number 1
!
interface GigabitEthernet0
no ip address
!
interface GigabitEthernet1
no ip address
!
interface GigabitEthernet2
no ip address
!
interface GigabitEthernet3
no ip address
!
interface GigabitEthernet4
no ip address
!
interface GigabitEthernet5
no ip address
!
interface GigabitEthernet6
no ip address
!
interface GigabitEthernet7
no ip address
!
interface GigabitEthernet8
no ip address
shutdown
duplex auto
speed auto
!
interface Vlan1
ip address 192.168.1.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface Dialer0
mtu 1492
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer-group 1
ppp authentication pap chap ms-chap callin
ppp chap hostname xxx@xxxx.xx
ppp chap password 0 xxxxxx
ppp ipcp address accept
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
ip nat pool LAN 192.168.1.0 192.168.1.254 netmask 255.255.255.0
ip nat inside source list LAN interface Dialer0 overload <--- I have also tryed with: ip nat inside source list LAN interface Ethernet0.101 overload
ip route 0.0.0.0 0.0.0.0 Dialer0
!
ip access-list standard LAN
permit 192.168.1.0 0.0.0.255
!
ipv6 ioam timestamp
!
!
control-plane
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
!
line con 0
no modem enable
line aux 0
line vty 0 4
login
transport input none
!
scheduler allocate 20000 1000
!
end
01-24-2021 09:00 AM
Hello,
I think on the 897, the subinterface goes on interface GigabitEthernet8. Try the config below (important parts marked in bold
Current configuration : 2645 bytes
!
! Last configuration change at 14:39:38 UTC Sun Jan 24 2021
!
version 15.7
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
ip dhcp excluded-address 192.168.1.1 192.168.1.99
ip dhcp excluded-address 192.168.1.200 192.168.1.254
!
ip dhcp pool LAN
network 192.168.1.0 255.255.255.0
dns-server 9.9.9.9
default-router 192.168.1.254
!
--> ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
license udi pid C897VA-K9 sn FCZ201790ZL
!
redundancy
!
controller VDSL 0
!
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
!
interface BRI0
no ip address
encapsulation hdlc
shutdown
isdn termination multidrop
!
interface Ethernet0
no ip address
shutdown
!
interface Ethernet0
!
interface GigabitEthernet0
no ip address
!
interface GigabitEthernet1
no ip address
!
interface GigabitEthernet2
no ip address
!
interface GigabitEthernet3
no ip address
!
interface GigabitEthernet4
no ip address
!
interface GigabitEthernet5
no ip address
!
interface GigabitEthernet6
no ip address
!
interface GigabitEthernet7
no ip address
!
--> interface GigabitEthernet8.101
--> encapsulation dot1q 101
--> pppoe enable group-global
--> pppoe-client dial-pool-number 1
no ip address
duplex auto
speed auto
!
interface Vlan1
ip address 192.168.1.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface Dialer0
mtu 1492
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer-group 1
ppp authentication pap chap ms-chap callin
ppp chap hostname xxx@xxxx.xx
ppp chap password 0 xxxxxx
ppp ipcp address accept
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
--> ip nat inside source list 1 interface Dialer0 overload
!
--> ip route 0.0.0.0 0.0.0.0 Dialer0
!
--> access-list 1 permit 192.168.1.0 0.0.0.255
!
--> dialer-list 1 protocol ip permit
!
ipv6 ioam timestamp
!
control-plane
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
line con 0
no modem enable
line aux 0
line vty 0 4
login
transport input none
!
scheduler allocate 20000 1000
!
end
01-24-2021 10:56 AM
Heya,
Something has changed when show ip interface brief but still no ping to the internet, same from Compuyer behind the NAT.
Two commends didn't pass for interface GigabitEthernet8.101. I'd bold them.
Router# show ip interface brief
Interface IP-Address OK? Method Status Protocol
ATM0 unassigned YES NVRAM administratively down down
BRI0 unassigned YES NVRAM administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
Dialer0 unassigned YES manual up up
Ethernet0 unassigned YES NVRAM administratively down down
GigabitEthernet0 unassigned YES unset down down
GigabitEthernet1 unassigned YES unset down down
GigabitEthernet2 unassigned YES unset down down
GigabitEthernet3 unassigned YES unset down down
GigabitEthernet4 unassigned YES unset down down
GigabitEthernet5 unassigned YES unset down down
GigabitEthernet6 unassigned YES unset down down
GigabitEthernet7 unassigned YES unset down down
GigabitEthernet8 unassigned YES NVRAM administratively down down
GigabitEthernet8.101 unassigned YES unset administratively down down
NVI0 unassigned YES unset up up
Virtual-Access1 unassigned YES unset up up
Vlan1 192.168.1.254 YES manual down down
Router#
Router#show run
Building configuration...
Current configuration : 2512 bytes
!
! Last configuration change at 18:12:16 UTC Sun Jan 24 2021
!
version 15.7
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
!
!
ip dhcp excluded-address 192.168.1.1 192.168.1.99
ip dhcp excluded-address 192.168.1.200 192.168.1.254
!
ip dhcp pool LAN
network 192.168.1.0 255.255.255.0
dns-server 9.9.9.9
default-router 192.168.1.254
!
!
!
ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
license udi pid C897VA-K9 sn FCZ201790ZL
!
!
!
redundancy
!
!
controller VDSL 0
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
!
interface BRI0
no ip address
encapsulation hdlc
shutdown
isdn termination multidrop
!
interface Ethernet0
no ip address
shutdown
!
interface GigabitEthernet0
no ip address
!
interface GigabitEthernet1
no ip address
!
interface GigabitEthernet2
no ip address
!
interface GigabitEthernet3
no ip address
!
interface GigabitEthernet4
no ip address
!
interface GigabitEthernet5
no ip address
!
interface GigabitEthernet6
no ip address
!
interface GigabitEthernet7
no ip address
!
interface GigabitEthernet8
no ip address
shutdown
duplex auto
speed auto
!
interface GigabitEthernet8.101
encapsulation dot1Q 101
pppoe enable group global
pppoe-client dial-pool-number 1
<—- Router(config-subif)#duplex auto
<—- % Invalid input detected at '^' marker.
<—— Router(config-subif)#speed auto
<—— % Invalid input detected at '^' mark
!
interface Vlan1
ip address 192.168.1.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface Dialer0
mtu 1492
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer-group 1
ppp authentication pap chap ms-chap callin
ppp chap hostname xxx@xxx.xx
ppp chap password 0 xxxxx
ppp ipcp address accept
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
ip nat inside source list 1 interface Dialer0 overload
ip route 0.0.0.0 0.0.0.0 Dialer0
!
dialer-list 1 protocol ip permit
ipv6 ioam timestamp
!
access-list 1 permit 192.168.1.0 0.0.0.255
!
control-plane
!
!
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
!
!
!
!
!
line con 0
no modem enable
line aux 0
line vty 0 4
login
transport input none
!
scheduler allocate 20000 1000
!
!
!
!
!
!
!
end
01-24-2021 11:08 AM
Hello,
you need to 'no shut' interface GigabitEthernet8:
Router#conf t
Router(config)#interface GigabitEthernet8
Router(config-if)#no shut
01-24-2021 12:40 PM
Now in the config it's:
!
interface GigabitEthernet8
no ip address
duplex auto
speed auto
!
But anyway it's down:
Router#show ip interface brief
Interface IP-Address OK? Method Status Protocol
ATM0 unassigned YES NVRAM administratively down down
BRI0 unassigned YES NVRAM administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
Dialer0 unassigned YES NVRAM up up
Ethernet0 unassigned YES NVRAM administratively down down
GigabitEthernet0 unassigned YES unset down down
GigabitEthernet1 unassigned YES unset down down
GigabitEthernet2 unassigned YES unset down down
GigabitEthernet3 unassigned YES unset down down
GigabitEthernet4 unassigned YES unset down down
GigabitEthernet5 unassigned YES unset down down
GigabitEthernet6 unassigned YES unset down down
GigabitEthernet7 unassigned YES unset down down
GigabitEthernet8 unassigned YES NVRAM down down
GigabitEthernet8.101 unassigned YES unset down down
NVI0 unassigned YES unset up up
Virtual-Access1 unassigned YES unset up up
Vlan1 192.168.1.254 YES NVRAM down down
Router#
01-24-2021 12:59 PM
Hello,
on which port is the ISP/cable modem connected ? Is that GigabitEthernet8 ?
01-24-2021 01:09 PM
01-24-2021 02:38 PM
Hello,
try the ATM interface configuration marked in bold:
Current configuration : 2645 bytes
!
! Last configuration change at 14:39:38 UTC Sun Jan 24 2021
!
version 15.7
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
no aaa new-model
!
ip dhcp excluded-address 192.168.1.1 192.168.1.99
ip dhcp excluded-address 192.168.1.200 192.168.1.254
!
ip dhcp pool LAN
network 192.168.1.0 255.255.255.0
dns-server 9.9.9.9
default-router 192.168.1.254
!
--> ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
license udi pid C897VA-K9 sn FCZ201790ZL
!
redundancy
!
controller VDSL 0
!
interface ATM0
no ip address
--> ip nat outside
--> ip virtual-reassembly
no atm ilmi-keepalive
--> pvc 8/35
--> encapsulation aal5mux ppp dialer
--> dialer pool-member 1
!
--> dsl operating-mode auto
!
interface BRI0
no ip address
encapsulation hdlc
shutdown
isdn termination multidrop
!
interface Ethernet0
no ip address
shutdown
!
interface Ethernet0
!
interface GigabitEthernet0
no ip address
!
interface GigabitEthernet1
no ip address
!
interface GigabitEthernet2
no ip address
!
interface GigabitEthernet3
no ip address
!
interface GigabitEthernet4
no ip address
!
interface GigabitEthernet5
no ip address
!
interface GigabitEthernet6
no ip address
!
interface GigabitEthernet7
no ip address
!
interface GigabitEthernet8
no ip address
!
interface Vlan1
ip address 192.168.1.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface Dialer0
mtu 1492
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer-group 1
ppp authentication pap chap ms-chap callin
ppp chap hostname xxx@xxxx.xx
ppp chap password 0 xxxxxx
ppp ipcp address accept
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
--> ip nat inside source list 1 interface Dialer0 overload
!
--> ip route 0.0.0.0 0.0.0.0 Dialer0
!
--> access-list 1 permit 192.168.1.0 0.0.0.255
!
--> dialer-list 1 protocol ip permit
!
ipv6 ioam timestamp
!
control-plane
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
line con 0
no modem enable
line aux 0
line vty 0 4
login
transport input none
!
scheduler allocate 20000 1000
!
end
01-25-2021 02:14 PM
Hello,
Thank You for still having patience for this.
Router(config-if)#do show ip int brie
Interface IP-Address OK? Method Status Protocol
ATM0 unassigned YES NVRAM down down
BRI0 unassigned YES NVRAM administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
Dialer0 unassigned YES NVRAM up up
Ethernet0 unassigned YES NVRAM administratively down down
GigabitEthernet0 unassigned YES unset down down
GigabitEthernet1 unassigned YES unset down down
GigabitEthernet2 unassigned YES unset down down
GigabitEthernet3 unassigned YES unset down down
GigabitEthernet4 unassigned YES unset down down
GigabitEthernet5 unassigned YES unset down down
GigabitEthernet6 unassigned YES unset down down
GigabitEthernet7 unassigned YES unset down down
GigabitEthernet8 unassigned YES NVRAM administratively down down
GigabitEthernet8.101 unassigned YES unset deleted down
NVI0 unassigned YES unset up up
Virtual-Access1 unassigned YES unset up up
Virtual-Access2 unassigned YES unset up up
Vlan1 192.168.1.254 YES NVRAM down down
Router(config-if)#
Here is runnning-config:
Building configuration...
Current configuration : 2436 bytes
!
version 15.7
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
!
!
!
ip dhcp excluded-address 192.168.1.1 192.168.1.99
ip dhcp excluded-address 192.168.1.200 192.168.1.254
!
ip dhcp pool LAN
network 192.168.1.0 255.255.255.0
dns-server 9.9.9.9
default-router 192.168.1.254
!
!
!
ip cef
no ipv6 cef
!
!
!
!
!
multilink bundle-name authenticated
!
!
!
license udi pid C897VA-K9 sn FCZ201790ZL
!
!
!
redundancy
!
!
!
!
!
controller VDSL 0
!
interface ATM0
no ip address
ip nat outside
ip virtual-reassembly in
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
!
<—— Router(config-if)#dsl operating-mode auto
^
<—% Invalid input detected at '^' marker.
!
interface BRI0
no ip address
encapsulation hdlc
shutdown
isdn termination multidrop
!
interface Ethernet0
no ip address
shutdown
!
interface GigabitEthernet0
no ip address
!
interface GigabitEthernet1
no ip address
!
interface GigabitEthernet2
no ip address
!
interface GigabitEthernet3
no ip address
!
interface GigabitEthernet4
no ip address
!
interface GigabitEthernet5
no ip address
!
interface GigabitEthernet6
no ip address
!
interface GigabitEthernet7
no ip address
!
interface GigabitEthernet8
no ip address
shutdown
duplex auto
speed auto
!
interface Vlan1
ip address 192.168.1.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface Dialer0
mtu 1492
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer-group 1
ppp authentication pap chap ms-chap callin
ppp chap hostname jfthfojf@bn24.pl
ppp chap password 0 xxxxx
ppp ipcp address accept
!
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
ip nat inside source list 1 interface Dialer0 overload
ip route 0.0.0.0 0.0.0.0 Dialer0
!
dialer-list 1 protocol ip permit
ipv6 ioam timestamp
!
access-list 1 permit 192.168.1.0 0.0.0.255
!
control-plane
!
!
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
!
!
!
line con 0
no modem enable
line aux 0
line vty 0 4
login
transport input none
!
scheduler allocate 20000 1000
!
!
!
end
01-25-2021 02:49 PM
Hello,
we are missing something fundamental. What country are you in, and who is your ISP ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide