This is the config for the 3845 that I dial-in to.
!
version 12.3
!
ip domain name tac.XXX.XX.XXX
ip name-server XXX.XXX.XXX.XXX
ip name-server 10.40.0.1
ip address-pool local
multilink virtual-template 1
no ftp-server write-enable
async-bootp dns-server 10.40.0.2
async-bootp nbns-server 10.40.0.2
!
chat-script cisco-default ABORT ERROR "" "AT Z" OK "ATDT \T" TIMEOUT 30 \c CONNECT \c
!
interface Loopback0
ip address 10.40.10.6 255.255.255.252
!
interface GigabitEthernet0/0
description Connection To 5500
ip address 10.40.0.243 255.255.255.0
duplex auto
speed 100
media-type rj45
!
interface Virtual-Template1
ip unnumbered GigabitEthernet0/0
peer default ip address pool localpool
ppp authentication chap
ppp multilink
!
interface Group-Async1
ip unnumbered GigabitEthernet0/0
encapsulation ppp
async mode interactive
peer default ip address pool localpool
ppp multilink
group-range 1/0 1/15
!
interface Group-Async2
ip unnumbered GigabitEthernet0/0
encapsulation ppp
async mode interactive
peer default ip address pool localpool
ppp multilink
group-range 2/0 2/15
!
router eigrp 1
network 10.0.0.0
no auto-summary
!
ip local pool localpool 10.40.0.15 10.40.0.30
ip default-gateway 10.40.0.254
ip classless
ip route 0.0.0.0 0.0.0.0 10.40.0.254
ip dns server
!
control-plane
!
!
line aux 0
script dialer cisco-default
login local
modem InOut
transport input all
autoselect during-login
autoselect ppp
stopbits 1
flowcontrol hardware
line 1/0 1/15
script dialer cisco-default
login local
modem InOut
transport input all
autoselect during-login
autoselect ppp
stopbits 1
speed 115200
flowcontrol hardware
line 2/0 2/15
script dialer cisco-default
login local
modem InOut
transport input all
autoselect during-login
autoselect ppp
stopbits 1
speed 115200
flowcontrol hardware
!
scheduler allocate 20000 1000
!
end
Here is the config for the 2821 that dial-out.
version 12.3
!
hostname CENTRALTC1
!
boot-start-marker
!
interface Loopback0
ip address 10.40.10.5 255.255.255.252
!
interface Multilink1
no ip address
ppp multilink
ppp multilink group 1
!
interface GigabitEthernet0/0
description interface to Vault Van Network
ip address 10.40.3.254 255.255.255.0
duplex auto
speed auto
no mop enabled
!
interface Virtual-Template1
description Virtual Template for Mutlilink Users
ip unnumbered Loopback0
ppp authentication chap
ppp multilink
!
interface Async1/0 SAME FOR ASYNC 1/1- 1/3
no ip address
encapsulation ppp
dialer in-band
dialer pool-member 1
dialer idle-timeout 0 either
dialer-group 1
async default routing
async mode interactive
no peer default ip address
no fair-queue
pulse-time 1
ppp authentication chap callin
ppp multilink
!
interface Dialer1
ip address negotiated
encapsulation ppp
dialer pool 1
dialer remote-name 3800sipr
dialer wait-for-carrier-time 60
dialer string 739xxx1
dialer string 739xxx2
dialer string 739xxx3
dialer string 739xxx4
dialer load-threshold 1 outbound
dialer max-call 4
dialer persistent
dialer-group 1
no cdp enable
ppp authentication chap
ppp multilink
!
router eigrp 1
timers active-time disabled
network 10.0.0.0
no auto-summary
eigrp stub connected summary
!
ip default-gateway 10.40.10.6
ip classless
ip route 0.0.0.0 0.0.0.0 10.40.0.243
ip http server
!
!
access-list 101 permit icmp any any
access-list 101 permit ip any any
dialer-list 1 protocol ip list 101
!
control-plane
!
!
line con 0
exec-timeout 0 0
logging synchronous
line aux 0
line 1/0 1/15
modem InOut
transport input all
stopbits 1
speed 115200
flowcontrol hardware
!
scheduler allocate 20000 1000
end
The modems dial all the same router. When I tried EIGRP it would work as long as I didn't try to use more than one computer on the network.
Jeff
