cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
774
Views
0
Helpful
1
Replies

DOT1Q Trunk between 6500 with CatOS / IOS and 2621

mccmhtac1
Level 1
Level 1

I need to setup a vlan between 3 devices that will tolk over the WAN.

Device 1

6509 with CatOS / IOS

ON MSFC:

Interface Vlan 200

ip address 10.10.10.1 255.255.255.248

On switch:

set vtp domain mccmh

set vlan 200  7/37

set port speed      7/37  100

clear trunk 7/37 1-199,201-699,701-1005,1025-4094

set trunk 7/37 on dot1q 200,700,1006-1024

et spantree portfast    7/37 enable trunk

Device 2:

On 2600 Router:

interface FastEthernet0/0

description OPTEMAN ERS Interface

no ip address

speed 100

half-duplex

!

interface FastEthernet0/0.100

bandwidth 10000

encapsulation dot1Q 200

ip address 10.10.10.2 255.255.255.248

On the 6509 here are the sh logs:

show port capabilities 7/37

Model                    WS-X6148-GE-TX

Port                     7/37

Type                     10/100/1000

Speed                    auto,10,100,1000,auto-10-100

Duplex                   half,full

Trunk encap type         802.1Q

Trunk mode               on,off,desirable,auto,nonegotiate

Channel                  yes

Broadcast suppression    no

Flow control             receive-(off,on,desired),send-(off,on,desired)

Security                 yes

Dot1x                    yes

Membership               static,dynamic

Fast start               yes

QOS scheduling           rx-(1q2t),tx-(1p2q2t)

CoS rewrite              yes

ToS rewrite              DSCP

UDLD                     yes

Inline power             no

AuxiliaryVlan            1..1000,1025..4094,untagged,dot1p,none

SPAN                     source,destination

COPS port group          7/25-48

Link debounce timer      yes

Dot1q-all-tagged         yes

Auto MDIX                yes

Jumbo frames             no

sh port 7/37

* = Configured MAC Address

# = 802.1X Authenticated Port Name.

Port  Name                 Status     Vlan       Duplex Speed       Type

----- -------------------- ---------- ---------- ------ ----------- ------------

7/37                      connected  trunk        half         100 10/100/1000

sh trunk

* - indicates vtp domain mismatch

# - indicates dot1q-all-tagged enabled on the port

$ - indicates non-default dot1q-ethertype value

Port      Mode         Encapsulation  Status        Native vlan

--------  -----------  -------------  ------------  -----------

7/37     on           dot1q          trunking      200

15/1      nonegotiate  isl            trunking      1

16/1      nonegotiate  isl            trunking      1

Port      Vlans allowed on trunk

--------  ---------------------------------------------------------------------

7/37     200,700,1006-1024

15/1      1-4094

16/1      1-4094

Port      Vlans allowed and active in management domain

--------  ---------------------------------------------------------------------

7/37     200

15/1      10,20,30,100-101,200

16/1

Port      Vlans in spanning tree forwarding state and not pruned

--------  ---------------------------------------------------------------------

7/37     200

15/1      10,20,30,100-101,200

16/1

-----------and on the 2600 ------------------------

CCESSRTR1#sh int fa0/0.100

FastEthernet0/0.100 is up, line protocol is up

  Hardware is AmdFE, address is 0007.851b.d540 (bia 0007.851b.d540)

  Internet address is 10.10.10.2/29

  MTU 1500 bytes, BW 10000 Kbit, DLY 100 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation 802.1Q Virtual LAN, Vlan ID  200.

  ARP type: ARPA, ARP Timeout 04:00:00

THe lines how connect and sh cdp nei shows the other side.

I cannot ping in either direction to a ip in the vlan 200 (10.10.10.1-3)

What am I missing?

Thanks

1 Reply 1

Leo Laohoo
Hall of Fame
Hall of Fame

Duplicate post. 

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: