Fiber cable + 3845 router SFP slot

[satishmothukri]

Hi All ,

3845 router is placed at customer location and is connected to core switch using fiber cable.

I Would like to know the type of fiber cable which is being used to connect router and switch ie LC or SC type cable.Is there any document available in cisco site which provides information about cable type for 3845 router SFP slot.

Picture is enclosed with this mail.

Cisco 3845 (revision 1.0) with 221184K/40960K bytes of memory.

Processor board ID FHK1020F2T2

3 FastEthernet interfaces

2 Gigabit Ethernet interfaces

2 Serial interfaces

2 Channelized E1/PRI ports

1 Virtual Private Network (VPN) Module

1 Subrate T3/E3 port

DRAM configuration is 64 bits wide with parity enabled.

479K bytes of NVRAM.

62720K bytes of ATA System CompactFlash (Read/Write)

Configuration register is 0x2102

Slot 0:

        C3845 Mother board 1GE(TX,SFP),1GE(TX), integrated VPN and 4W Port adapter, 7 ports

        Port adapter is analyzed

wr2#sh int g0/0

GigabitEthernet0/0 is up, line protocol is up

  Hardware is BCM1125 Internal MAC, address is 0017.949a.3ed0 (bia 0017.949a.3ed0)

  Internet address is 10.x.x.x /29

  MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,

     reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA, loopback not set

  Keepalive set (10 sec)

Full-duplex, 1000Mb/s, link type is autonegotiation, media type is SX

Thanks ,
M S K       

[satishmothukri]

Below is show controller output

---------------------------------------------

wr2#sh controllers

Interface GigabitEthernet0/0 (idb 0x65239118)

Hardware is BCM1125 Internal MAC (Revision A3)

  Network connection mode is AUTO

  network link is up

  Config is 1Gbps, Full Duplex

  Selected media-type is SFP

  SFP type is 1000BaseSX

MAC Registers:

ds->rx_all_multicast = 0x659C8F50

  mac_hash_0_0 =   0x0000000000000000

  mac_hash_1_0 =   0x0000000000000000

  mac_hash_2_0 =   0x0000000400000000

  mac_hash_3_0 =   0x0000000000000000

  mac_hash_4_0 =   0x0000000000000000

  mac_hash_5_0 =   0x0000000000000000

  mac_hash_6_0 =   0x2000000000000000

  mac_hash_7_0 =   0x0000000000000000

  mac_admask_0 =     0x0000FFFFFFFFFFFF, mac_admask_1  = 0x0000000000000000

  mac_cfg =          0x000000C8000A0176, mac_thrsh_cfg = 0x0000080400087804

  mac_vlantag =      0x0000000000000000, mac_frame_cfg = 0x05F4400000280200

  mac_adfilter_cfg = 0x0000000000000E28, mac_enable    = 0x0000000000000C11

  mac_status =       0x0000000000000000, mac_int_mask  = 0x00004F0000C300C3

  mac_txd_ctl =      0x000000000000000F, mac_eth_addr  = 0x0000D03E9A941700

  mac_fifo_ptrs =    0x05F4400000280200, mac_eopcnt    = 0x000044003A3A3A3A

  MAC RX is enabled  RX DMA - channel 0 is enabled, channel 1 is disabled

  MAC TX is enabled  TX DMA - channel 0 is enabled, channel 1 is disabled

  Device status = 1000 Mbps, Full-Duplex

Thanks ,
M S K