01-23-2007 04:18 AM - edited 03-03-2019 03:27 PM
This has been set up to dial back to our DBU router. Do these configs look correct. These are the errors that I am getting in the routers log.Could this be a service provider issue or a mis-config issue. Please help ASAP. I will rate.
%ISDN-6-LAYER2DOWN: Layer 2 for Interface Se3/2:23, TEI 0 changed to down
%ISDN-6-LAYER2UP: Layer 2 for Interface Se3/2:23, TEI 0 changed to up
Remote site
interface BRI0/0
description Dial Backup to <router hostname> Dialer 251
ip address x.x.x.x x.x.x.x
encapsulation ppp
ip summary-address eigrp 100 x.x.x.x x.x.x.x 5
carrier-delay msec 0
dialer idle-timeout 30
dialer string <number>
dialer load-threshold 1 outbound
dialer watch-disable 15
dialer watch-group 1
dialer-group 1
isdn switch-type basic-net3
ppp authentication chap
ppp multilink
end
interface Dialer XXX
description Dialer-Profile for <rtr name> (Dialer-xxx)
ip unnumbered Loopback251
encapsulation ppp
ip summary-address eigrp 100 x.x.x.x x.x.x.x 5
ip summary-address eigrp 100 x.x.x.x x.x.x.x 175
ip policy route-map < policy name>
dialer pool 251
dialer remote-name <rtr hostname>
dialer idle-timeout 0
dialer string <Number>
dialer load-threshold 1 outbound
dialer max-call 2
dialer-group 1
no peer default ip address
no cdp enable
ppp authentication chap
ppp multilink
end
01-23-2007 04:58 AM
Josh:
The errors that you are seeing is referring to the D-Channel off the ISDN PRI T-1 that you must have. Probably the line is configured wrong or the line is down from the carrier. You need to do a show controller T-1 for the port and see if you are getting any errors or alarms off the T-1. Can you provide the configuration off the router with the T-1. Just the T-1 config and ISDN configs...Thanks...
01-23-2007 05:36 AM
This is the layer 2 debug output that I got.
Jan 23 08:24:27.855: ISDN Se2/2:23 Q921: User TX -> RRp sapi=0 tei=0 nr=126
Jan 23 08:24:27.859: ISDN Se2/2:23 Q921: User RX <- RRf sapi=0 tei=0 nr=114
Jan 23 08:24:28.659: ISDN Se2/3:23 Q921: User TX -> RRp sapi=0 tei=0 nr=8
Jan 23 08:24:28.663: ISDN Se2/3:23 Q921: User RX <- RRf sapi=0 tei=0 nr=100
Jan 23 08:24:32.775: ISDN Se3/2:23 Q921: User TX -> RRp sapi=0 tei=0 nr=0
Jan 23 08:24:32.923: ISDN Se3/2:23 Q921: User RX <- RRp sapi=0 tei=0 nr=0
Jan 23 08:24:32.927: ISDN Se3/2:23 Q921: User TX -> RRf sapi=0 tei=0 nr=0
Jan 23 08:24:33.775: ISDN Se3/2:23 Q921: User TX -> RRp sapi=0 tei=0 nr=0
Jan 23 08:24:34.775: ISDN Se3/2:23 Q921: User TX -> RRp sapi=0 tei=0 nr=0
Jan 23 08:24:35.775: ISDN Se3/2:23 Q921: User TX -> RRp sapi=0 tei=0 nr=0
Jan 23 08:24:36.775: ISDN Se3/2:23 Q921: User TX -> SABMEp sapi=0 tei=0
Jan 23 08:24:37.775: ISDN Se3/2:23 Q921: User TX -> SABMEp sapi=0 tei=0
Jan 23 08:24:38.063: ISDN Se2/0:23 Q921: User TX -> RRp sapi=0 tei=0 nr=72
Jan 23 08:24:38.067: ISDN Se2/0:23 Q921: User RX <- RRf sapi=0 tei=0 nr=117
Jan 23 08:24:38.775: ISDN Se3/2:23 Q921: User TX -> SABMEp sapi=0 tei=0
Jan 23 08:24:39.775: ISDN Se3/2:23 Q921: User TX -> SABMEp sapi=0 tei=0
Jan 23 08:24:40.775: %ISDN-6-LAYER2DOWN: Layer 2 for Interface Se3/2:23, TEI 0 changed to down
Jan 23 08:24:40.779: ISDN Se3/2:23 Q921: User TX -> SABMEp sapi=0 tei=0
Jan 23 08:24:41.687: ISDN Se3/0:23 Q921: User TX -> RRp sapi=0 tei=0 nr=110
Jan 23 08:24:41.691: ISDN Se3/0:23 Q921: User RX <- RRf sapi=0 tei=0 nr=57
Jan 23 08:24:41.779: ISDN Se3/2:23 Q921: User TX -> SABMEp sapi=0 tei=0
Jan 23 08:24:42.779: ISDN Se3/2:23 Q921: User TX -> SABMEp sapi=0 tei=0
Jan 23 08:24:43.779: ISDN Se3/2:23 Q921: User TX -> SABMEp sapi=0 tei=0
Jan 23 08:24:44.779: ISDN Se3/2:23 Q921: User TX -> SABMEp sapi=0 tei=0
Jan 23 08:24:44.783: ISDN Se3/2:23 Q921: User RX <- UAf sapi=0 tei=0
Jan 23 08:24:44.783: %ISDN-6-LAYER2UP: Layer 2 for Interface Se3/2:23, TEI 0 changed to up
Jan 23 08:24:45.367: ISDN Se2/1:23 Q921: User TX -> RRp sapi=0 tei=0 nr=79
Jan 23 08:24:45.371: ISDN Se2/1:23 Q921: User RX <- RRf sapi=0 tei=0 nr=127
Jan 23 08:24:47.207: ISDN Se4/0:23 Q921: User TX -> RRp sapi=0 tei=0 nr=41
Jan 23 08:24:47.211: ISDN Se4/0:23 Q921: User RX <- RRf sapi=0 tei=0 nr=22
Jan 23 08:24:47.583: ISDN Se3/1:23 Q921: User TX -> RRp sapi=0 tei=0 nr=12
Jan 23 08:24:47.587: ISDN Se3/1:23 Q921: User RX <- RRf sapi=0 tei=0 nr=124
Jan 23 08:24:47.591: ISDN Se3/3:23 Q921: User TX -> RRp sapi=0 tei=0 nr=116
Jan 23 08:24:47.595: ISDN Se3/3:23 Q921: User RX <- RRf sapi=0 tei=0 nr=2
The T-1 configs haven't changed they are the same they have been for a year. It was the ISDN congigs that were changed. This seems to be bouncing for the past couple days every 2-5 min. I opened a tkt with the lec they stated they couldn't loop our csu. Do you think this is a layer 2 issue and not a config issue?
01-23-2007 05:47 AM
This could be a layer 1 or layer 2 issue. Can you please provide the configurations for both routers...
01-23-2007 05:58 AM
It looks to be a LEC problem. The only reason I would suspect a mis-config is someone changed the config on the same day that it started having a problem. I am on the phone with the lec now trying to resolve this issue. Thank you very much for your help I will let you know how it goes.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: