cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
605
Views
0
Helpful
0
Replies
Highlighted
Beginner

HWIC-3G-HSPA and Optus

hi,

We have a 1921 router and 3g card. We have tested the 3G card in a PC and logged onto the networ successfully. We have setup the router with the below settings and the cell0/0/0 interface constantly bounces. Are there any Optus specific settings that need to be set in the card? Can you use AT commands on the card as reverse telnet does not seem to work?

Config:

nterface Cellular0/0/0

ip address negotiated

ip nat outside

ip virtual-reassembly in

encapsulation ppp

load-interval 30

shutdown

dialer in-band

dialer idle-timeout 0

dialer string optus

dialer-group 1

async mode interactive

ppp chap refuse

ppp pap sent-username tba password 7 xxxxxxxxxxxxxxxxxxx

ppp ipcp dns request

!

!

dialer-list 1 protocol ip permit

!

ip route 0.0.0.0 0.0.0.0 Cellular0/0/0

!

##show cellular 0/0/0 all
Hardware Information
====================
Modem Firmware Version = K2_0_7_19AP C:/WS/FW
Modem Firmware built = 10/26/09
Hardware Version = 1.0
International Mobile Subscriber Identity (IMSI) = 505023306092954
International Mobile Equipment Identity (IMEI) = 011955005278306
Integrated Circuit Card ID (ICCID) = 8961023312414003035
Mobile Subscriber International Subscriber
IDentity Number (MSISDN) =
Factory Serial Number (FSN) = C66188226171006
Modem Status = Online
Current Modem Temperature = 35 deg C, State = Normal
PRI SKU ID = 9992680, SKU Rev. = 1.3

Profile Information
====================
Profile password Encryption level: 7

Profile 1 = INACTIVE*
--------
PDP Type = IPv4
Access Point Name (APN) = fxauct
Authentication = PAP
Username: tba
Password: xxxxxxx

* - Default profile

Data Connection Information
===========================
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = INACTIVE
        Inactivity Reason = Unknown
Profile 2, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 3, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 4, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 5, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 6, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 7, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 8, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 9, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 10, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 11, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 12, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 13, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 14, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 15, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state
Profile 16, Packet Session Status = INACTIVE
        Inactivity Reason = Normal inactivate state

Network Information
===================
Current Service Status = Normal, Service Error = None
Current Service = Packet switched
Packet Service = UMTS/WCDMA (Attached)
Packet Session Status = Inactive
Current Roaming Status = Home
Network Selection Mode = Automatic
Country = AUS, Network = Optus
Mobile Country Code (MCC) = 505
Mobile Network Code (MNC) = 2
Location Area Code (LAC) = 32005
Routing Area Code (RAC) = 1
Cell ID = 0
Primary Scrambling Code = 477
PLMN Selection = Automatic
Registered PLMN =  , Abbreviated =
Service Provider = YES OPTUS

Radio Information
=================
Radio power mode = ON
Current Band = WCDMA 2100, Channel Number = 10737
Current RSSI(RSCP) = -105 dBm
Band Selected = Auto
Number of nearby cells = 1
Cell 1
        Primary Scrambling Code = 0x1DD
        RSCP = -103 dBm, ECIO = -5 dBm


Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3

Thanks

Everyone's tags (1)
CreatePlease to create content
Content for Community-Ad
July's Community Spotlight Awards