11-13-2013 12:09 PM - edited 03-04-2019 09:34 PM
Hi,
Trying to set up a new border gateway but the iBGP routes are not being installed and next hop is inaccessible. I use loopback interfaces and update-source. Am I missing something obvious?
Router 1 is ISR 2821, 12.4
Router 2 is 7301, 12.3
### gets all prefixes, not installed in routing table. next-hop is inaccessible.
rtr2#show ip bgp 8.8.8.8
BGP routing table entry for 8.8.8.0/24, version 0
Paths: (1 available, no best path)
Not advertised to any peer
33885 15169
84.246.88.35 (inaccessible) from 100.100.0.1 (195.67.149.10)
Origin IGP, metric 10, localpref 80, valid, internal
## No bgp routes in table
rtr2#show ip route | inc B
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
rtr2#
## config router 1
100.100.0.2 4 39302 21 77340 291227447 0 0 00:17:30 0
interface Loopback0
ip address 100.100.0.1 255.255.255.255
!
!
interface GigabitEthernet0/0.27
description iBGP link
encapsulation dot1Q 27
ip address 10.255.255.1 255.255.255.0
no ip proxy-arp
!
router bgp 65535
bgp router-id 195.67.149.10
no bgp fast-external-fallover
no bgp default ipv4-unicast
bgp log-neighbor-changes
neighbor 100.100.0.2 remote-as 65535
neighbor 100.100.0.2 ebgp-multihop 2
neighbor 100.100.0.2 update-source Loopback0
!
no synchronization
network 100.100.0.0 mask 255.255.224.0
neighbor 100.100.0.2 activate
default-metric 1
no auto-summary
exit-address-family
!
ip route 100.100.0.2 255.255.255.255 10.255.255.2
## config router 2
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
100.100.0.1 4 65535 154518 41 943080 0 0 00:16:57 469741
interface Loopback0
ip address 100.100.0.2 255.255.255.255
!
interface GigabitEthernet0/1.27
description iBGP link
encapsulation dot1Q 27
ip address 10.255.255.2 255.255.255.0
no ip proxy-arp
no snmp trap link-status
!
router bgp 65535
bgp router-id 100.100.0.2
no bgp fast-external-fallover
no bgp default ipv4-unicast
bgp log-neighbor-changes
neighbor 100.100.0.1 remote-as 65535
neighbor 100.100.0.1 description router01
neighbor 100.100.0.1 ebgp-multihop 2
neighbor 100.100.0.1 update-source Loopback0
!
address-family ipv4
neighbor 100.100.1 activate
no auto-summary
no synchronization
exit-address-family
!
ip route 212.112.0.1 255.255.255.255 10.255.255.1
Solved! Go to Solution.
11-13-2013 12:44 PM
Hi,
on r1:
router bgp 65535
neighbor 100.100.0.2 next-hop-self
Regards
Alain
Don't forget to rate helpful posts.
11-13-2013 12:44 PM
Hi,
on r1:
router bgp 65535
neighbor 100.100.0.2 next-hop-self
Regards
Alain
Don't forget to rate helpful posts.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: