cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

Community Helping Community

609
Views
4
Helpful
2
Replies
Highlighted
Beginner

Inactive Ports on 4507R-2 Switch

Hello!

I'm having issues getting the ports g3/5 and g4/5 from inactive to notconnect.

I have tried the hw-module uplink select all in the global configuratio, but it's not working, getting a : % Invalid input detected at '^' marker. Message every time.

This what I have:

Power consumed by backplane : 40 Watts

Mod Ports Card Type                              Model              Serial No.

---+-----+--------------------------------------+------------------+-----------

1    48  10/100/1000BaseT (RJ45)                WS-X4548-GB-RJ45   JAE152101QK

2    48  10/100/1000BaseT (RJ45)                WS-X4548-GB-RJ45   JAE15200382

3     6  Sup V-10GE 10GE (X2), 1000BaseX (SFP)  WS-X4516-10GE      JAE15120205

4     6  Sup V-10GE 10GE (X2), 1000BaseX (SFP)  WS-X4516-10GE      JAE150900XV

5    48  10/100/1000BaseT (RJ45)                WS-X4548-GB-RJ45   JAE1520026G

6    48  10/100/1000BaseT (RJ45)                WS-X4548-GB-RJ45   JAE152007T9

M MAC addresses                    Hw  Fw           Sw               Status

--+--------------------------------+---+------------+----------------+---------

1 4055.39a5.0120 to 4055.39a5.014f 2.6                               Ok      

2 6400.f1dd.2a40 to 6400.f1dd.2a6f 2.6                               Ok      

3 c471.feee.3940 to c471.feee.3945 5.2 12.2(31r)SGA 12.2(53)SG2      Ok      

4 c471.feee.3946 to c471.feee.394b 5.2 12.2(31r)SGA 12.2(53)SG2      Ok      

5 6400.f1dd.2470 to 6400.f1dd.249f 2.6                               Ok      

6 6400.f1dd.22f0 to 6400.f1dd.231f 2.6                               Ok      

Mod  Redundancy role     Operating mode      Redundancy status

----+-------------------+-------------------+----------------------------------

3   Active Supervisor   RPR                 Active                           

4   Standby Supervisor  RPR                 Standby cold                     

System Failures:

----------------

Power Supply:   bad/off (see 'show power')

GTADBHDDEISESAVGA01S11#sh int status mod 3            

Port      Name               Status       Vlan       Duplex  Speed Type

Te3/1     Not in Use         disabled     1            full    10G No X2

Te3/2     Not in Use         disabled     1            full    10G No X2

Gi3/3     Uplink to 3825 GTA notconnect   10           full   1000 1000BaseSX

Gi3/4     Uplink via FE Medi connected    trunk        full   1000 1000BaseSX

Gi3/5     Uplink via FE Medi inactive     1            full   1000 1000BaseSX

Gi3/6     Not in Use         disabled     1            full   1000 No Gbic

GTADBHDDEISESAVGA01S11#sh int status mod 4

Port      Name               Status       Vlan       Duplex  Speed Type

Te4/1     Not in Use         disabled     1            full    10G No X2

Te4/2     Not in Use         disabled     1            full    10G No X2

Gi4/3     Uplink to 3825 GTA notconnect   1110         full   1000 1000BaseSX

Gi4/4     Uplink via FE Medi connected    trunk        full   1000 1000BaseSX

Gi4/5     Uplink via FE Medi inactive     1            full   1000 1000BaseSX

Gi4/6     Not in Use         disabled     1            full   1000 No Gbic

Any help will be gratefull.

Cheers

-Jose

Everyone's tags (3)
2 REPLIES 2
Advisor

Inactive Ports on 4507R-2 Switch

Hopefully this will help:

http://www.cisco.com/en/US/products/hw/switches/ps708/products_tech_note09186a008015bfd6.shtml#inact

HTH,

John

HTH, John *** Please rate all useful posts ***
Beginner

Inactive Ports on 4507R-2 Switch

Hey John,

Thanks for the information, but I have tried the hw-module uplink select all command, and I'm getting an % Invalid input detected at '^' marker under uplink. I also used the ? to see what options are available after I right module, and after I right uplink. Still it does not bring the inactive ports up.

Thanks for the intel

-Jose

CreatePlease to create content
Content for Community-Ad
FusionCharts will render here