So I tried to upgrade from isr4400-universalk9.17.12.04b.SPA.bin to isr4400-universalk9.17.12.05a.SPA.bin. After the upgrade it will not register with my SIP provider. I see this. Aug 11 02:08:22.843: %SIP-3-REG_INTERNAL: Registration failed. Tenant=...
Forum Posts
Resolved! NTP ACL not working
Can someone please help me figure out why NTP is not being allowed when this ACL is applied inbound on the internet facing interface? everything else works but NTP broke and not sure why. interface GigabitEthernet0/0/0 ip address 1.2.3.4 6.7.8.9...
I have two fortigate firewalls on different subnet and I want to do routing between them on a layer 3 switch guide me on how to do that mind you that I still have my switch enabled for routing.The scenario is like this: the interface connected on the...
Hello I am working multiple setups but this one was supposed to be easy, until it was not. I am sure I am overlooking something tiny, but nevertheless. Long story short; here is my config and I get not get any NAT translations and or any internet a...
I have what appears on one level to be a basic question. I was tasked with coming up with a plan to support 2 remote sites that don’t have IT people. Each site has an ISR4400 series and a 9200 switch stack with 2 switches. There is a spare 4400 and a...
With Shankar SthanuretnamWelcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn from Cisco expert Shankar Sthanuretnam about next generation Network Based Application Recognition. (NBAR2) is a Deep Packet ...
Hello,I have a MPLS L2VPN between two Cisco NCS 5011 routers. Both of the devices are running 7.11.2. When I am trying to pass packets with TTL value 1 (any packets with other TTL values are passing OK), these packets are filtered:show lpts pifib har...
on Data center router ,we have 6 VRF and let say we have subnet 10.x.x.x/18 and this subnet route is seen in all 6 vrf on that Data center routeris it possible ?as i learnt that VRF creates separate routing table then how can we see one subnet rout...
Resolved! Cisco 1100 ISP Failover
Dear Forum,I'm reaching out for an issue I'm having with a Cisco 1100 running IOS 9.17.09.05. The router is connected to 2 WAN ports with a simple failover config. The primary WAN is on G0/0/0 and the backup is on G0/0/1. When ISP1 (ATT) drops, the d...
I have a Zyxel Firewall performing all the routing on my network which includes several VLAN's(VLAN10, 20, etc. I am having a disagreement with the vendor. The only way their device supports VLAN routing you have to set the profile up and map it to a...
I'm having a really difficult time getting TACACS working on a new ASR1001x. I have the device cabled on the management interface and I can ping the TACACS server. Management interface is in the Mgmt-intf VRF. Here is a copy of my config, where am...
Hi All, Am trying to advertise default router getting from Site01Edg101 over ISIS on RTR-PE-35 , and now try to adverstie this default route to VRF Cust-A using OSPF , but not able to succeed. Configs is mentioned below for some tips . Secondly I b...
Hello I will more generalize my system to get across the idea better. DSL Modem - FPR1010 - SG350XG. All ACL/NAT is done on FPR with a static route to find the 3 VLans on the SG350XG. [FPR 1/2 connects to SG 1/1] On SG I have 3 VLans and each VLan is...
Please i hope you can help me, I need the CAD drawing (DWG, DXF, or STEP) for the followings components: - IE 3000-8TC - PWR-IE65W-PC-AC= Thanks in advance, regards!
Hi All, Kindly advise if for deploying 8300 (C8300-1N1S-4T2X) as a redundant pair (HA) at internet edge , do we need to interlink the router's direct;y like how we do for core switches or do we just need to make redundant connectivty to wan and inter...
