09-22-2019 10:41 PM
Hi team,
I Have configured LACp configuration on SG 550 switch - after that i am getting following output,
Po2 Active: gi1-2
I Have configured for two Gigabit ethernet port but in active state it shows only one port Why ?
This is my switch Configuration
switch4fe4de#show running-config
config-file-header
switch4fe4de
v2.5.0.83 / RTESLA2.5_930_364_091
CLI v1.0
file SSD indicator encrypted
@
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
!
!
unit-type-control-start
unit-type unit 1 network gi uplink none
unit-type-control-end
!
vlan database
vlan 2,15-16
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
no boot host auto-config
no boot host auto-update
bonjour interface range vlan 1
hostname switch4fe4de
username admin password encrypted 7af2d10b73ab7cd8f603937f7697cb5fe432c7ff privilege 15
clock timezone J 0 minutes 0
!
interface vlan 2
ip address 192.168.137.3 255.255.255.128
!
interface vlan 16
ip address 192.168.139.65 255.255.255.248
!
interface GigabitEthernet1
no negotiation
spanning-tree link-type point-to-point
channel-group 2 mode on
switchport mode trunk
macro description switch
!next command is internal.
macro auto smartport dynamic_type switch
!
interface GigabitEthernet2
no negotiation
spanning-tree link-type point-to-point
channel-group 2 mode on
switchport mode trunk
macro description switch
!next command is internal.
macro auto smartport dynamic_type switch
!
interface GigabitEthernet3
no switchport
!
interface Port-Channel2
flowcontrol on
spanning-tree link-type point-to-point
switchport mode trunk
macro description switch
!next command is internal.
macro auto smartport dynamic_type switch
!
exit
ip default-gateway 192.168.139.66
In both switch side i have configured Lacp Auto only.
Please help me to complete the configuration with two enable ports.
Thanks,
Regards,
Yasmeen Shaul Hameed.
Solved! Go to Solution.
09-24-2019 06:26 AM
HI,
A few days ago, I faced the same issue and one port is getting suspended. I checked everything and found a bug with Cisco IOS. What is the firmware version?
Point: It is not recommended but you can try with restart both switches at same time.
09-22-2019 11:20 PM
Hi there,
What is the LACP state of the ports on the device(s) at the other end of the port-channel?
cheers,
Seb.
09-23-2019 12:32 AM
09-23-2019 12:52 AM
Hi there,
You have configured both ends with mode on, so this means LACP is not being used.
Try changing the channel-group commands on both ends to mode active.
Then share the output of sh etherchannel summary
cheers,
Seb.
09-23-2019 02:57 AM
09-23-2019 03:38 AM
OK, then put the SG550 end to mode auto and the other (IOS?) end to mode active.
Check the output to show etherchannel summary on the IOS switch.
cheers,
Seb.
09-23-2019 03:51 AM
09-23-2019 05:06 AM
My mistake.
In which case I suggest you test each LAG pair in isolation. Remove the channel-group config and shut down one of the interfaces of the pair.
Gi1 <---> Gi1/0/1
Gi2 (shutdown) <--> Gi2/0/1
Once tested, shut Gi1 and no shut Gi2.
This will confirm that the link is capable of being UP/UP and forwarding. It will be interesting to see if both links work when not bundled.
cheers,
Seb.
09-23-2019 06:14 AM
09-23-2019 07:28 AM
The SG documentation states that mode on doesn't use LACP negotiation. It is just bundling the links together. If there is an issue with a member link the LAG will not know it.
Auto mode is described differently to IOS. On IOS, auto is for PAgP, but the SGxxx uses it for LACP negotiation. on IOS having an auto<-->auto pair would not work. Perhaps the SGxxx will behave differently.
Perhaps try mode auto on both ends. You may end up with just one working member link, this indicates you have an issue with the other not becoming an active member of the bundle.
09-23-2019 08:01 AM
SG550 <-------> SG550 <------> SG550
do you mean 3 switches are involved?
or do you mean 2 switches ?
SG550 <-------> SG550
<------>
in the first situation you end up with two LAG groups each with a single interface!
09-23-2019 08:21 AM
09-23-2019 09:30 PM
09-24-2019 01:15 AM
"macro auto smartport dynamic_type switch"
I suggest a test with auto-smartports disabled or set manually instead of dynamic
"Auto Smartport waits for a device to be attached to the interface before applying a configuration. When a device is detected from an interface, the Smartport macro (if assigned) that corresponds to the Smartport type of the attaching device is automatically applied."
if the detection is not correct the wrong settings may be applied.
whether detection be correct or not, the macro may overrule your manual settings
09-24-2019 06:26 AM
HI,
A few days ago, I faced the same issue and one port is getting suspended. I checked everything and found a bug with Cisco IOS. What is the firmware version?
Point: It is not recommended but you can try with restart both switches at same time.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide