I am trying to connect a PT router to a WRT300N wireless router with a crossover cable or straight through. I want the PT router to be the gateway. I have the WRT300N router set up and connected to 2 PCs using WPA2 personal encryption.I am not sure h...
Forum Posts
IN-TN_CHN_BNG-INFONET# show interfaces po10 human-readablePort-channel10 is up, line protocol is upHardware is 10GEChannel, address is 5c5a.c700.8ec9 (bia 5c5a.c700.8ec9)Description: ## CONNECT-TO-INTERNET ROUTER ##Internet address is X.X.X.X/XMTU 92...
Hi! I have a problem with VRF NAT translations.We have a cisco 1111 router with following configuration:ip vrf WILDNETip vrf WILDNET_PTip vrf WILDNET_TMinterface GigabitEthernet0/0/0description outsideip vrf forwarding WILDNETip address 1.1.1.10 255....
Network scenario: ISP>CISCO Router> CISCO FTD > Core SW >Access SW > Serverwe have two public ip like 203.76.64.16/28 and like 203.76.64.64/26 here only 203.76.64.19 is my end and also 203.76.64.64/26 is used for only one to one NAT in FTD for my few...
I am trying to install c1117 router and soda on it ,I need help to install
Hi , am trying to advertise default Mgmt-Vrf route to GRT so that other devices reachable to default route . thanks for tips and tricks . Configuration is mentioned below . DC01-leaf03-55#show run int giga0/0interface GigabitEthernet0/0vrf forwardin...
I have a project here for a simple network in Cisco Packet Tracer. All connections respond when pinged, but the laptop connected wirelessly with the WRT300N router cannot be pinged from outside the network. The laptop itself can ping any other device...
My inside trunked router port randomly shuts, with no indication of why in the logs. I had debug STP. What's another debug I can enable to try and get an idea why?Router Log Dec 3 2025 01:26:37 UTC: %TRACK-6-STATE: 22 interface Gi0/0/1.2 ip routing U...
So, I am dealing with PLC one one side...10/100mbps port. Via a single mode Fibre cable it is extended to the switch cabinet. I am suppose to select the Switch & SFP. Can someone with experience validate the selection that I derived as : Cisco GLC-FE...
Hello I had trtied to apply this scenario to my FPR1010 but either due to lack of understand or simply did not fit my needs, I decided the FPR1010 was a Firewall {obviously) and decided to let it be such and work on the ISRC1111. What I have posted b...
Hello Expert,I’m seeking best-practice guidance for an OSPF hub-and-spoke design and would appreciate feedback on my proposed Area placement.Network summarySites: 5 (1 HQ hub + 4 remote spokes)Requirement: Spokes must only communicate with the Hub; n...
Use Space Bar to simulate Break Key Sequence Read this article if you are trying to generate a Break Key Sequence to access ROMmon, and the Break Key sequence does NOT seem to make it to the router.Today, I needed to access ROMmon on an IR1101 Indust...
I'm working through getting IOS-XR devices to ZTP.I'm using DHCP Option 67 to pass the URL for a ztp python script.The DHCP offer also includes DNS server options.It seems that if the URL uses FQDN in the URL, the ZTP script will not be downloaded.On...
Hello,I have Cisco C1121-4P Router with Sec9 License, I need to configure Remote Access VPN - like Anyconnect, is it possible?
Hello, does anyone have this in .pkt i just wanna config it
