cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
4793
Views
0
Helpful
4
Replies

My WAN interface is not reachable (CISCO 1811 router).

MUKADI Pierre
Level 1
Level 1

My router has two WAN Interfaces :

I use the f1 for all my vlans (16). Internally, all things work. All my vlans are reachables and can ping my internals LAN subinterfaces (f1.1, f1.2, etc.).

But my WAN still stay unreacheable. Here is it config :

Has you can see on my show interface commande, FastEthernet0 is up, line protocol is up

# show interface

FastEthernet0 is up, line protocol is up

Hardware is PQ3_TSEC, address is c471.fe2f.acc6 (bia c471.fe2f.acc6)

Internet address is w.x.y.18/29

MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Full-duplex, 100Mb/s, 100BaseTX/FX

ARP type: ARPA, ARP Timeout 04:00:00

Last input 00:00:00, output 00:00:09, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/40 (size/max)

5 minute input rate 0 bits/sec, 1 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

5027 packets input, 462139 bytes

Received 1479 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 watchdog

0 input packets with dribble condition detected

1206 packets output, 73180 bytes, 0 underruns

0 output errors, 0 collisions, 2 interface resets

5 unknown protocol drops

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

# show ip route

Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2

i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2

ia - IS-IS inter area, * - candidate default, U - per-user static route

o - ODR, P - periodic downloaded static route

Gateway of last resort is w.x.y.17 to network 0.0.0.0

w.0.0.0/8 is variably subnetted, 2 subnets, 2 masks

C w.x.y.16/29 is directly connected, FastEthernet0

S w.0.0.0/8 [1/0] via w.x.y.16

10.0.0.0/24 is subnetted, 14 subnets

C 10.10.1.0 is directly connected, FastEthernet1.1

C 10.10.2.0 is directly connected, FastEthernet1.2

C 10.10.3.0 is directly connected, FastEthernet1.3

C 10.10.4.0 is directly connected, FastEthernet1.4

C 10.10.5.0 is directly connected, FastEthernet1.5

C 10.10.6.0 is directly connected, FastEthernet1.6

C 10.10.7.0 is directly connected, FastEthernet1.7

C 10.10.8.0 is directly connected, FastEthernet1.8

C 10.10.9.0 is directly connected, FastEthernet1.9

C 10.10.10.0 is directly connected, FastEthernet1.10

C 10.10.11.0 is directly connected, FastEthernet1.11

C 10.10.12.0 is directly connected, FastEthernet1.12

C 10.10.13.0 is directly connected, FastEthernet1.13

C 10.10.14.0 is directly connected, FastEthernet1.14

# sho ip nat stat

Total active translations: 6 (2 static, 4 dynamic; 4 extended)

Peak translations: 7, occurred 00:46:39 ago

Outside interfaces:

FastEthernet0

Inside interfaces:

FastEthernet1.1, FastEthernet1.2, FastEthernet1.3, FastEthernet1.4

FastEthernet1.5, FastEthernet1.6, FastEthernet1.7, FastEthernet1.8

FastEthernet1.9, FastEthernet1.10, FastEthernet1.11, FastEthernet1.12

FastEthernet1.13, FastEthernet1.14

# show run

...

dot11 syslog

ip source-route

!

!

ip dhcp excluded-address 10.10.10.1

!

ip dhcp pool ccp-pool

import all

network 10.10.10.0 255.255.255.248

default-router 10.10.10.1

lease 0 2

!

!

ip cef

no ip domain lookup

ip domain name unikis.cd

ip name-server 10.10.1.3

ip name-server w.x.y.17

ip name-server a.b.c.d

ip name-server 10.10.1.4

ip dhcp-server 10.10.1.3

no ipv6 cef

!

multilink bundle-name authenticated

!

!

!

username root privilege 15 secret 5 $1$f5k4$q3SYzlWss5D04R5ttstcU.

...

!

interface FastEthernet0

ip address w.x.y.18 255.255.255.248

ip access-group 112 in

ip verify unicast source reachable-via any

ip helper-address w.x.y.17

ip helper-address a.b.c.d

no ip unreachables

ip nat outside

ip virtual-reassembly

duplex auto

speed auto

!

interface FastEthernet1

no ip address

ip nat allow-static-host

ip nat enable

duplex auto

speed auto

!

interface FastEthernet1.1

encapsulation dot1Q 1 native

ip address 10.10.1.1 255.255.255.0

ip helper-address 10.10.1.3

ip nat inside

ip virtual-reassembly

no cdp enable

!

...

!

interface Async1

no ip address

encapsulation slip

!

ip default-gateway 10.10.1.1

ip forward-protocol nd

ip route 0.0.0.0 0.0.0.0 w.x.y.17

ip route w.0.0.0 255.0.0.0 w.x.y.16

ip route w.0.0.0 255.0.0.0 w.x.y.16

ip http server

ip http access-class 23

ip http authentication local

ip http secure-server

ip http timeout-policy idle 60 life 86400 requests 10000

!

!

But the f0 still stay unreacheable. Not even self pings do work.

Help, please !!!!!!!

4 Replies 4

cflory
Level 1
Level 1

First thing I'd check, is to see if the ACL you have applied to that interface is causing a connectivity problem (remove it temporarily to confirm).  Next I'd check your network mask on that interface and make sure it matches the upstream router.

-Chris

Thanks for you answer Chris.

Nothing change when removing the ACL.

The ip adress and mask was used on a small linksys router : E3200 (I have access to Internet if I use it). The network address is 85.31.68.16/29. Even if you ping my gateway it works, but on my router (WAN interface) I have an ICMP unreachable message (even self ping on the router doesn't work). I have the same message when i ping it from an other computer (on wan side) ?!!!!

try this.

Remove

ip verify unicast source reachable-via any

ip nat outside

from Fa0/0

just for test and see if it makes any difference

Thanks for all. Just changing the interface (Fa1 for WAN and Fa0 for subnetting) the problem was resolved. I don't understand but this was the solution. Now I can ping all my interface but I reach an other problem : (external) DNS and NAT overload (PAT) do not work. (I must replace my linsys by my cisco 1811).

Here are my configuration and the test I did :

current configuration : 7853 bytes

!

version 12.4

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname MAIN

!

boot-start-marker

boot-end-marker

!

logging message-counter syslog

...

!

no aaa new-model

!

!

dot11 syslog

ip source-route

!ip cef

ip name-server 10.10.1.3

ip name-server 10.10.1.4

ip name-server 85.31.68.17

ip name-server 80.251.0.4

no ipv6 cef

!

multilink bundle-name authenticated

!

!

!

archive

log config

  hidekeys

!

!

interface FastEthernet0

interface FastEthernet0

no ip address

duplex auto

speed auto

!

interface FastEthernet0.1

encapsulation dot1Q 1 native

ip address 10.10.1.1 255.255.255.0

ip access-group 111 in

ip helper-address 10.10.1.3

ip helper-address 10.10.1.4

ip helper-address 85.31.68.17

ip helper-address 80.251.0.4

ip nat inside

ip virtual-reassembly

!

interface FastEthernet0.2

encapsulation dot1Q 2

ip address 10.10.2.1 255.255.255.0

ip access-group 111 in

ip helper-address 10.10.1.3

ip helper-address 10.10.1.4

ip nat inside

ip nat inside

ip virtual-reassembly

!

interface FastEthernet0.3

encapsulation dot1Q 3

ip address 10.10.3.1 255.255.255.0

ip access-group 111 in

ip helper-address 10.10.1.3

ip helper-address 10.10.1.4

ip nat inside

ip virtual-reassembly

!

...

interface FastEthernet1

ip address 85.31.68.18 255.255.255.248

ip access-group 112 in

ip helper-address 85.31.68.17

ip helper-address 80.251.0.4

ip helper-address 85.31.68.20

ip nat outside

ip virtual-reassembly

duplex auto

speed auto

!

!

ip default-gateway 85.31.68.17

ip forward-protocol nd

ip route 85.0.0.0 255.0.0.0 85.31.68.16

ip route 85.31.68.16 255.255.255.248 FastEthernet1

no ip http server

no ip http secure-server

!

!

ip nat source static 10.10.1.3 85.31.68.20

ip nat inside source list 111 interface FastEthernet1 overload

ip nat inside source static 10.10.1.2 85.65.30.19

ip nat inside source static 10.10.1.3 85.65.30.20

!

access-list 111 permit ip 10.10.1.0 0.0.0.255 any

access-list 111 permit udp 10.10.1.0 0.0.0.255 85.31.68.0 0.0.0.248 eq domain

access-list 111 permit ip host 10.10.1.3 any

access-list 111 permit icmp any any

access-list 111 permit tcp any 85.31.68.16 0.0.0.7 eq www

access-list 111 permit tcp any 85.31.68.16 0.0.0.7 eq 8080

access-list 111 permit tcp any 85.31.68.16 0.0.0.7 eq pop3

access-list 111 permit tcp any 85.31.68.16 0.0.0.7 eq 22

access-list 111 permit udp any 85.31.68.16 0.0.0.7 eq domain

access-list 111 permit tcp any 85.31.68.16 0.0.0.7 eq telnet

access-list 111 permit tcp any 85.31.68.16 0.0.0.7 eq smtp

access-list 111 permit tcp any 85.31.68.16 0.0.0.7 eq 143

access-list 111 permit tcp any 85.31.68.16 0.0.0.7 eq 123

access-list 111 permit udp any 85.31.68.16 0.0.0.7 eq ntp

access-list 111 permit udp any 85.31.68.16 0.0.0.7 eq snmp

access-list 111 permit tcp any 85.31.68.16 0.0.0.7 eq 443

access-list 111 permit tcp any 85.31.68.16 0.0.0.7 eq ftp-data

access-list 111 permit tcp any 85.31.68.16 0.0.0.7 eq ftp

access-list 111 permit tcp any host 10.10.1.2 eq www

access-list 111 permit tcp any host 10.10.1.2 eq 8080

access-list 111 permit tcp any host 10.10.1.2 eq pop3

access-list 111 permit tcp any host 10.10.1.2 eq 443

access-list 111 permit tcp any host 10.10.1.2 eq 143

access-list 111 permit tcp any host 10.10.1.2 eq 22

access-list 111 permit udp any host 10.10.1.3 eq domain

access-list 111 permit tcp any host 10.10.1.2 eq 445

access-list 111 permit udp any host 10.10.1.3 eq bootps

ccess-list 111 permit udp any host 10.10.1.3 eq bootpc

access-list 111 permit udp any host 10.10.1.3 eq 389

access-list 111 permit tcp any host 10.10.1.3 eq 389

access-list 111 permit tcp any host 10.10.1.3 eq 636

access-list 111 permit icmp any host 10.10.1.3

access-list 111 permit ip host 10.10.2.26 any

access-list 111 permit ip host 10.10.2.25 any

access-list 111 permit udp any 10.10.1.0 0.0.0.255 eq bootps

access-list 111 permit udp any 10.10.1.0 0.0.0.255 eq bootpc

access-list 111 permit tcp any 10.10.1.0 0.0.0.255 eq 68

access-list 111 permit tcp any 10.10.1.0 0.0.0.255 eq 67

access-list 112 permit tcp any 85.31.68.16 0.0.0.7 eq www

access-list 112 permit tcp any 85.31.68.16 0.0.0.7 eq 8080

access-list 112 permit tcp any 85.31.68.16 0.0.0.7 eq 22

access-list 112 permit tcp any 85.31.68.16 0.0.0.7 eq 443

access-list 112 permit udp any 85.31.68.16 0.0.0.7 eq domain

access-list 112 permit icmp any 85.31.68.16 0.0.0.7

access-list 112 permit icmp any 0.0.0.2 255.255.255.248

access-list 113 permit ip host 10.10.1.3 any

!

!

TEST :

------

MAIN#sho ip nat statist

Total active translations: 40 (2 static, 38 dynamic; 38 extended)

Peak translations: 45, occurred 00:01:35 ago

Outside interfaces:

  FastEthernet1

Inside interfaces:

  FastEthernet0.1, FastEthernet0.2, FastEthernet0.3, FastEthernet0.4

  FastEthernet0.5, FastEthernet0.6, FastEthernet0.7, FastEthernet0.8

  FastEthernet0.9, FastEthernet0.10, FastEthernet0.11, FastEthernet0.12

  FastEthernet0.13, FastEthernet0.14, FastEthernet0.15, FastEthernet0.16

Hits: 1252  Misses: 0

CEF Translated packets: 556, CEF Punted packets: 431

Expired translations: 250

Dynamic mappings:

-- Inside Source

[Id: 1] access-list 111 interface FastEthernet1 refcount 28

Appl doors: 0

Normal doors: 0

Queued Packets: 0

MAIN#debug ip nat

IP NAT debugging is on

MAIN#

*May 25 15:41:33.363: NAT: s=10.10.1.3->85.65.30.20, d=85.31.68.17 [46997]

*May 25 15:41:33.731: NAT*: s=10.10.1.3->85.65.30.20, d=85.31.68.17 [0]

*May 25 15:41:33.955: NAT: expiring 85.31.68.18 (10.10.1.58) udp 49743 (49743)

*May 25 15:41:33.955: NAT: expiring 85.31.68.18 (85.31.68.18) udp 1133 (49743)

*May 25 15:41:34.035: NAT: s=10.10.1.3->85.65.30.20, d=85.31.68.17 [46998]

MAIN#

*May 25 15:41:34.739: NAT*: s=10.10.1.3->85.65.30.20, d=85.31.68.17 [0]

MAIN#

*May 25 15:41:35.747: NAT*: s=10.10.1.3->85.65.30.20, d=85.31.68.17 [0]

*May 25 15:42:05.367: NAT: s=10.10.1.58->85.31.68.18, d=85.31.68.17 [19340]

*May 25 15:42:05.711: NAT: expiring 85.31.68.18 (10.10.1.58) udp 57847 (57847)

*May 25 15:42:05.711: NAT: expiring 85.31.68.18 (85.31.68.18) udp 1137 (57847)

*May 25 15:42:05.987: NAT*: s=10.10.1.3->85.65.30.20, d=85.31.68.17 [0]

*May 25 15:42:06.995: NAT*: s=10.10.1.3->85.65.30.20, d=85.31.68.17 [0]

*May 25 15:42:07.083: NAT: s=10.10.1.58->85.31.68.18, d=85.31.68.17 [19347]

*May 25 15:42:07.555: NAT: s=10.10.1.58->85.31.68.18, d=85.31.68.17 [19351]

*May 25 15:42:07.759: NAT: expiring 85.65.30.20 (10.10.1.3) udp 25102 (25102)

*May 25 15:42:07.759: NAT: expiring 85.31.68.18 (10.10.1.58) udp 62831 (62831)

*May 25 15:42:07.759: NAT: expiring 85.31.68.18 (85.31.68.18) udp 1138 (62831)

MAIN#

*May 25 15:42:46.983: NAT*: s=10.10.1.58->85.31.68.18, d=85.31.68.17 [19579]

*May 25 15:42:46.983: NAT*: s=85.31.68.17, d=85.31.68.18->10.10.1.58 [37775]

*May 25 15:42:47.983: NAT*: s=10.10.1.58->85.31.68.18, d=85.31.68.17 [19588]

*May 25 15:42:47.983: NAT*: s=85.31.68.17, d=85.31.68.18->10.10.1.58 [37776]

MAIN#ping 85.31.68.17

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 85.31.68.17, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms

MAIN#ping 173.194.69.94

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 173.194.69.94, timeout is 2 seconds:

.....

Success rate is 0 percent (0/5)

MAIN#ping google.fr

Translating "google.fr"...domain server (10.10.1.3) (10.10.1.4) (85.31.68.17) (8

0.251.0.4)

% Unrecognized host or address, or protocol not running.

MAIN#show ip route

...

Gateway of last resort is not set

     85.0.0.0/8 is variably subnetted, 2 subnets, 2 masks

C       85.31.68.16/29 is directly connected, FastEthernet1

S       85.0.0.0/8 [1/0] via 85.31.68.16

     10.0.0.0/24 is subnetted, 16 subnets

C       10.10.1.0 is directly connected, FastEthernet0.1

C       10.10.2.0 is directly connected, FastEthernet0.2

C       10.10.3.0 is directly connected, FastEthernet0.3

...

MAIN#show protocol

Global values:

  Internet Protocol routing is enabled

  Async1 is down, line protocol is down

FastEthernet0 is up, line protocol is up

FastEthernet0.1 is up, line protocol is up

  Internet address is 10.10.1.1/24

FastEthernet0.2 is up, line protocol is up

  Internet address is 10.10.2.1/24

FastEthernet0.3 is up, line protocol is up

  Internet address is 10.10.3.1/24

...

FastEthernet1 is up, line protocol is up

  Internet address is 85.31.68.18/29

Vlan1 is up, line protocol is down

Is there anything wrong ?  :-(

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco