02-11-2021 06:50 PM
Need help.
This should be fairly simply.....however. I have a C9500-16X that has routing enabled(couple of ports routed working with neighbors)that I'm trying to establish a neighbor relation with an old C3560X(:c3560e-universalk9-mz.152-4.E10.bin) enabled. The links are up, I can ping each side of the link, however no neighbor can be establish.
See below
9500 config:
interface TenGigabitEthernet1/0/16
description Link<>VG0202 Gateway
no switchport
ip address 10.13.255.13 255.255.255.252
############################
router ospf 100
router-id 10.13.255.100
passive-interface default
no passive-interface TenGigabitEthernet1/0/1
network 10.13.187.16 0.0.0.7 area 0.0.0.0
network 10.13.255.12 0.0.0.3 area 0.0.0.0
network 10.13.0.0 0.0.255.255 area 0.0.0.0
######################################
BTRBRGBBCFH9500_1#sho cdp nei te1/0/16 de
-------------------------
Device ID: CFHSurgVG_Sw1.ghsbtr.net
Entry address(es):
IP address: 10.13.255.14
Platform: cisco WS-C3560X-24P, Capabilities: Router Switch IGMP
Interface: TenGigabitEthernet1/0/16, Port ID (outgoing port): GigabitEthernet1/ 1
Holdtime : 143 sec
Version :
Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 15.2(4)E10, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2020 by Cisco Systems, Inc.
Compiled Tue 31-Mar-20 21:44 by prod_rel_team
advertisement version: 2
VTP Management Domain: ''
Duplex: full
Management address(es):
IP address: 10.13.255.14
Cisco 3560X config:
interface GigabitEthernet1/1
description Link<>9400-port 16
no switchport
ip address 10.13.255.14 255.255.255.252
end
####################################
CFHSurgVG_Sw1#sho run | b router ospf 100
router ospf 100
router-id 10.13.255.101
network 10.13.187.16 0.0.0.7 area 0.0.0.0
network 10.13.255.12 0.0.0.3 area 0.0.0.0
#######################################
CFHSurgVG_Sw1#sho cdp nei gi1/1 de
-------------------------
Device ID: BTRBRGBBCFH9500_1.ghsbtr.net
Entry address(es):
IP address: 10.13.255.13
Platform: cisco C9500-16X, Capabilities: Router Switch IGMP
Interface: GigabitEthernet1/1, Port ID (outgoing port): TenGigabitEthernet1/0/16
Holdtime : 135 sec
Version :
Cisco IOS Software [Fuji], Catalyst L3 Switch Software (CAT9K_IOSXE), Version 16.9.3, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2019 by Cisco Systems, Inc.
Compiled Wed 20-Mar-19 08:02 by mcpre
advertisement version: 2
VTP Management Domain: 'GHSDOMAIN_MT3'
Duplex: full
Management address(es):
IP address: 10.13.255.13
Any ideas!!!!!!!!!!!!!!!!!!
02-11-2021 07:54 PM
On the 9500, you have passive interface default enabled. You will have to issue the following command to allow OSPF adjacencies to form on the port:
no passive-interface TenGigabitEthernet1/0/16
02-11-2021 11:46 PM
Do the same config on Cisco 3560X (Some IOS by default passive-interface) - test and advise.
router ospf 100
no passive-interface GigabitEthernet1/1
Cat 9500
router ospf 100
no passive-interface TenGigabitEthernet1/0/16
02-12-2021 12:41 AM
Out of curiosity, which IOS versions have OSPF set to passive-interface default, by default ?
02-12-2021 02:27 AM
@Georg Pauwen apologies may be mixed up auto-summary vs passive interface. (Some IOS by default passive-interface)
02-12-2021 09:45 AM
Hello
Assuming it just a paste typo and you have indeed allowed that interface to be non passive as suggested by @Tyson Joachims
what sdm template is being used?
can you post output of:
debug up ospf adj
02-14-2021 12:44 PM
Assuming that the original post was accurate then passive interface was an issue. I would like to hear from the original poster about whether the passive interface has been corrected and whether there are any remaining issues.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide