poe log messages on a 857

arunjangid · ‎10-04-2012

hi all,

i have noticed poe log messages in my cisco 857 router, looking around there is mention of a cosmetic ios bug pertaining to 877 router but not the 857.

BUG - CSCsd68389. any suggestions as to why i am getting these errors on my 857?

001586: Oct 5 11:25:06.499 NZST: esw_dtc_ltc4258_reg_write: no acknowlege from POE

001587: Oct 5 11:25:06.499 NZST: esw_mrvl_pdc_hardware_config failed on slot 0/0

001601: Oct 5 13:06:29.879 NZST: esw_dtc_ltc4258_reg_write: no acknowlege from POE

001602: Oct 5 13:06:29.879 NZST: esw_mrvl_pdc_hardware_config failed on slot 0/0

001603: Oct 5 13:06:31.387 NZST: esw_dtc_ltc4258_reg_write: no acknowlege from POE

001604: Oct 5 13:06:31.387 NZST: esw_mrvl_pdc_hardware_config failed on slot 0/0

Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(9)T, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Sat 17-Jun-06 04:43 by prod_rel_team

ROM: System Bootstrap, Version 12.3(8r)YI2, RELEASE SOFTWARE

myrtr uptime is 1 week, 2 hours, 57 minutes

System returned to ROM by reload at 11:03:16 NZST Fri Sep 28 2012

System restarted at 11:03:54 NZST Fri Sep 28 2012

System image file is "flash:c850-advsecurityk9-mz.124-9.T.bin"

Cisco 857 (MPC8272) processor (revision 0x200) with 59392K/6144K bytes of memory.

Processor board ID FHK102120HB

MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10

4 FastEthernet interfaces

1 ATM interface

128K bytes of non-volatile configuration memory.

20480K bytes of processor board System flash (Intel Strataflash)

Configuration register is 0x2102

singhaam007 · ‎10-04-2012

Hello,

it seems to when when no POE module installed.

http://www.dslreports.com/forum/r21510313-LAN-error

https://supportforums.cisco.com/thread/188382

hope this will help.

thanks

Sandeep Choudhary · ‎10-05-2012

Hi Arun,

Try this:

these messages are related to the Power-over-Ethernet (PoE) module. Are you using one?

If you use the PoE module, connect all four Ethernet cables on the PoE module to the four LAN Ethernet ports on the Cisco router.(It is important to connect ALL FOUR Ethernet cables).

To ensure proper PoE module operation, first connect ALL 4 cables to the switch ports. Then, apply power to the PoE module. Do not connect the PoE module power supply to the PoE module before you connect the PoE module to the router.

or

Step1: Check the cables connection.

Step2: If all are ok then see the POE module(U hv POE module installed ?)

Step3: If still this problem Exists then u have problem with IOS.

similer problem links given by Amrinder, please see and try to solve the issue!

Regards

Please rate if it helps.

arunjangid · ‎10-07-2012

sorry i didnt mention in the orignal question, that i am not using a POE module. Checked ethernet cables, looked to be plugged in alright. but still am getting these messages. got some today morning.

002119: Oct 8 06:39:37.674 NZST: esw_dtc_ltc4258_reg_write: no acknowlege from POE

002120: Oct 8 06:39:37.674 NZST: esw_mrvl_pdc_hardware_config failed on slot 0/0

002121: Oct 8 06:39:39.182 NZST: esw_dtc_ltc4258_reg_write: no acknowlege from POE

002122: Oct 8 06:39:39.182 NZST: esw_mrvl_pdc_hardware_config failed on slot 0/0