cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
4074
Views
0
Helpful
7
Replies

PPP Multipoint (Inactive) - ???

mccmhtac1
Level 1
Level 1

I am configuring PPP Multipoint on a 6509 and a 2621

Here is the output of sh ppp multilink on the 6509:

No active bundles

Multilink1 (inactive)
  Member links: 3
    Se8/0/0:0 (inactive)
    Se8/0/1:0 (inactive)
    Se8/0/2:0 (inactive)

Here is the output of sh ppp multilink on the 2600:

No active bundles

Multilink1 (inactive)
  Member links: 3
    Se0/1 (inactive)
    Se0/2 (inactive)
    Se0/3 (inactive)

Here is the 6509 config:

interface Multilink1

ip address 100.1.1.1 255.255.255.252

ppp multilink

multilink-group 1

!

interface Serial8/0/0:0

description FN Multilink Interface 1

no ip address

encapsulation ppp

no fair-queue

ppp multilink

multilink-group 1

!

interface Serial8/0/1:0

description FN Multilink Interface 2

no ip address

encapsulation ppp

no fair-queue

ppp multilink

multilink-group 1

!

interface Serial8/0/2:0

description FN Multilink Interface 3

no ip address

encapsulation ppp

no fair-queue

ppp multilink

multilink-group 1

!

Here is the 2600 config:

interface Multilink1

ip address 100.1.1.2 255.255.255.252

service-policy output voice-policy

ppp multilink

multilink-group 1

!

interface Serial0/1

description FN Multilink INT 3

no ip address

encapsulation ppp

ppp multilink

multilink-group 1

!

interface Serial0/2

description FN Multilink INT 2

no ip address

encapsulation ppp

ppp multilink

multilink-group 1

!

interface Serial0/3

description FN Multilink INT 1

no ip address

encapsulation ppp

ppp multilink

multilink-group 1

!
interface Serial0/1
description FN Multilink INT 3
no ip address
encapsulation ppp
ppp multilink
multilink-group 1
!
interface Serial0/2
description FN Multilink INT 2
no ip address
encapsulation ppp
ppp multilink
multilink-group 1
!
interface Serial0/3
description FN Multilink INT 1
no ip address
encapsulation ppp
ppp multilink
multilink-group 1
!

any ideas???

7 Replies 7

mccmhtac1
Level 1
Level 1

The 2600 config double pasted it should be this:

Here is the 2600 config:

interface Multilink1

ip address 100.1.1.2 255.255.255.252

service-policy output voice-policy

ppp multilink

multilink-group 1

!

interface Serial0/1

description FN Multilink INT 3

no ip address

encapsulation ppp

ppp multilink

multilink-group 1

!

interface Serial0/2

description FN Multilink INT 2

no ip address

encapsulation ppp

ppp multilink

multilink-group 1

!

interface Serial0/3

description FN Multilink INT 1

no ip address

encapsulation ppp

ppp multilink

multilink-group 1

!

Hi Brian,

Seems like your are using controller on 6509.

If yes, can you check if controller 8/0/0 , 8/0/1 and 8/0/2 is no shut.

Regards,

Smitesh

I went into each controller and did a not shut. The multilinks show inactive on both the 2600 and 6509.  The three T1s are all up and running. Each shows line up, protocol down.

More 6509 config:

controller T1 8/0/0

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/1

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/2

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/3

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/4

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/5

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/6

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/7

framing esf

clock source internal

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/0

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/1

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/2

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

controller T1 8/0/0

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/1

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/2

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/3

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/4

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/5

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/6

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/7

framing esf

clock source internal

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/0

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/1

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/2

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

I tried doing a no shut on the 3 controlles. The T1s are up and running. Each shows line up and protocol down.

Yes I tried doing a no shut on each. The T1s show line up, protocol down.

Here is the controller config on the 6509. Do the three controllers

(8/0/0 - 2) need to be in the same channel group?

controller T1 8/0/0

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/1

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/2

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/3

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/4

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/5

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/6

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 8/0/7

framing esf

clock source internal

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/0

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/1

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

!

controller T1 9/0/2

framing esf

linecode b8zs

channel-group 0 timeslots 1-24

Can you also add command clock source line under controller config ?

I moved the config to another 2PA Flexwan Module and the Multilink came

up. I apparently have a bad module. Thanks for all your help.

Review Cisco Networking for a $25 gift card