09-01-2022 01:21 PM - edited 09-02-2022 09:32 AM
Hello community,
I'm facing the following problem, I appreciate if you can help me.
I am upgrading ROMMON from an ASR-903 from version 15.6(43r)S to 15.6(48r)S. and the following process was carried out:
ASR-903#upgrade rom-monitor filename bootflash:IOS-3.18.8aSP/asr900_15_6_48r_s_rommon.pkg all
Upgrade rom-monitor on Route-Processor 0
Target copying rom-monitor image file
Checking upgrade image...
1966080+0 records in
3840+0 records out
Upgrade image MD5 signature is
Burning upgrade partition...
1966080+0 records in
1966080+0 records out
Checking upgrade partition...
1966080+0 records in
1966080+0 records out
Upgrade flash partition MD5 signature is
ROMMON upgrade complete.
To make the new ROMMON permanent, you must restart the RP.
ASR-903#sh pla
ASR-903#sh platform
Chassis type: ASR-903
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
0/0 A900-IMA2Z ok 00:02:57
0/1 A900-IMA2Z ok 00:02:56
0/3 A900-IMA8S ok 00:02:55
0/4 A900-IMA8S ok 00:02:55
R0 A900-RSP2A-64 ok, active 00:05:11
F0 ok, active 00:05:11
P0 A900-PWR550-A ok 00:04:29
P1 A900-PWR550-A ok 00:04:27
P2 A903-FAN-E ok 00:04:24
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
R0 1905200E 15.6(43r)S
F0 1905200E 15.6(43r)S
ASR-903#wr
Building configuration...
[OK]!
ASR-903#reload
Proceed with reload? [confirm]
Aug 27 00:39:39.906 R0/0: %PMAN-5-EXI
System Bootstrap, Version 15.6(43r)S, RELEASE SOFTWARE (fc1)
Technical Support: https://protect-eu.mimecast.com/s/5ODNCGZ1ou0gDDWluY_Dse?domain=cisco.com
Copyright (c) 2020 by cisco Systems, Inc.
Compiled Mon 18-May-20 03:52 by pallavik
Initializing the PCI..
PCIe link training done..FPGA vendor ID[0x5f1137]
pci configuration done..
RSP2-64 P2 Board(1200 MHz). FPGA-325T
Current image running: Boot ROM0
Last reset cause: RSP-Board
Rommon upgrade requested
Directory .rommon_upgrade/rommon.bin not found
Unable to locate .rommon_upgrade/rommon.bin directory
Unable to load .rommon_upgrade/rommon.bin
Failed to upgrade ROMMON
Configuring zarlink...
Cylon-1 vendor ID[0x5e1137]
Cylon-2 vendor ID[0xffffffff]
pci configuration done..
Cylon Detected Success
C-Inlet temp 32C
UEA platform with 3670016 Kbytes of main memory
Rommon upgrade requested
Maximum upgrade attempts exceeded, continuing with old Rommon...
Located IOS-3.18.8aSP/packages.conf
What problem should be the source of the output shown:
Directory .rommon_upgrade/rommon.bin not found
Unable to locate .rommon_upgrade/rommon.bin directory
Unable to load .rommon_upgrade/rommon.bin
Failed to upgrade ROMMON?
09-02-2022 12:08 AM
- Ref : https://www.cisco.com/c/en/us/td/docs/routers/asr903/upgrade/guide/b-upgrade-3x-16x-asr900/m-upgrade-rommon-rsp-asr900.html#Cisco_Task_in_List_GUI.dita_f4b5ec41-239f-45af-a1c8-15c8f3862e13 , following Steps 2 and Steps 3 accordingly the pkg file must be in root-directory of bootflash. Try accordingly and or follow exact command sequence.
M.
09-02-2022 05:26 AM
Is it possible then that the reported error is due to the .pkg file not being directly in the bootflash: but in the bootflsh:IOS-3.18.8aSP/ directory?
And referring to the command, it must be applied:
upgrade rom-monitor filename bootflash:asr900_15_6_48r_s_rommon.pkgall
instead of:
upgrade rom-monitor filename bootflash:asr900_15_6_48r_s_rommon.pkg all
?
09-02-2022 06:04 AM
09-02-2022 06:07 AM
So the complete output would be:
#upgrade rom-monitor filename asr900_15_6_48r_s_rommon.pkg all
right?
09-02-2022 06:47 AM
09-02-2022 06:57 AM
Thank you for your help.
I will do it this way.
09-02-2022 07:24 AM
I did it this way and the problem continued.
Same output:
Rommon upgrade requested
Directory .rommon_upgrade/rommon.bin not found
Unable to locate .rommon_upgrade/rommon.bin directory
Unable to load .rommon_upgrade/rommon.bin
Failed to upgrade ROMMON
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide