Use Space Bar to simulate Break Key Sequence Read this article if you are trying to generate a Break Key Sequence to access ROMmon, and the Break Key sequence does NOT seem to make it to the router.Today, I needed to access ROMmon on an IR1101 Indust...
Forum Posts
I know this is not a putty forum, but I thought that some of you may be using this. I am trying to use Putty pscp to transfer files to and from my routers. I can pull files from the router with no problem. When I try to push a file to the router, it ...
Someone asked me what does protocol field 0 indicates in IP header?? It's confusing since protocol field only indicates upper layer protocol and 0 is used for IP Right??
hi,I have two routers that are part of asymtric connection toward exernal partner. Sometimes traffic from one sesion goes over one router and returnes over another and that is fine. I have monitor capture session that captures some traffic and becaus...
I have two PEs connected with one CE each, both of the PEs are connecting to one RR1. RR is recieving the routes from PEs and it is sending them as well but for some reason PEs are not installing the routes.RR1router bgp 65000bgp cluster-id 100bgp lo...
I am testing a dual-ISP setup at home to see how routing impacts online gaming performance. The goal is to:Use ISP1 for general traffic (browsing, downloads, streaming).Route gaming traffic (PUBG, Free Fire, COD Mobile, etc.) through ISP2 for lower l...
I am simulating a simple network technology with IOU L3 images and observe a strange behavior with image version 17.15.1The network consists of 4 routers, One of them is named a "SourcePC" (bottom of diagram) - a router from which I do an ICMP ping (...
Resolved! Redistribute static Ospf
Hi all, i have topologi forti(as a router internet &mpls) - Core switch - Palo-Alto ( FW server Farm) Connection core to forti using ip p2p & static default route 0.0.0.0/0 for access internet & access MPLS, Connection core to Palo-Alto using ip p2p ...
Has Cisco made any progress in updating this feature request to support the full Root-Intermediate CA validation?
Hello Dears,In our environment, we have a Cisco 2911 Router (IOS). We are now planning to replace it with a Cisco C8200L Router (IOS-XE). In the old router, we have BVI implemented. Since this feature is called BDI in IOS-XE, I have migrated the conf...
Hello,I have in my enterprise many dynamic routing protocols, within VRF and without VRF, like , EIGRP, OSPF, eBGP, ISIS and static routing.Im good with those and dont need to do any kind of upgrade.I have MPLS L2 VPN/MPLS L3 VPN , MPLS TE and IP Rou...
Resolved! Routing External IP via VPN Tunnels
I hope someone can help me find an answer to this scenario. We have another organization with which we have a site-to-site tunnel. This tunnel is located at our home office. Our remote sites have site-to-site tunnels to the home office. The other org...
I see that the lower ASR100x-X routers are already EOL. For the ASR1006-X and ASR1009-X there are no EOL dates out. Does anybody have any information on the expected lifespan of these components?
I'm curious what the difference is between the following log entries: %IOSXE_SPA-6-UPDOWN: Interface TenGigabitEthernet0/3/0, link down due to remote fault%IOSXE_SPA-6-UPDOWN: Interface TenGigabitEthernet0/3/0, link down due to local fault What would...
Hello all,I'm having trouble getting my BGP peers to show up in the VPNv4 BGP peering output.For example, if I have a very simple topology of 2 routers directly connected, and I run simple BGP between them using the IP on the directly connected link ...
