Router can't resolve domain names

[jfriend29]

First off I'm a cisco noob so I relialize I'm probably asking a rediculous question.  I am currently setting up a UC540 that I bought used that does not have a configuration. The problem I have encountered is the router is capable of pinging IP addresses but is unable to ping domain names. Furthermore I am unable to access internet resources from my workstation that is directly connected to the router. The router is directly connected to my cable modem.

I started over again from scratch and only have what I believe to be the bare minimum in the config to get started. My current config is as follows:

Building configuration...

Current configuration : 1849 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
!
!
!
!
!
dot11 syslog
ip source-route
ip cef
!
!
!
!
ip name-server 207.255.0.130
ip name-server 207.255.0.131
no ipv6 cef
!
!
!
!
multilink bundle-name authenticated
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
voice-card 0
!
!
!
license udi pid UC540W-FXO-K9 sn FGL160527A1
!
!
!
archive
log config
  hidekeys
!
!
!
!
!
interface FastEthernet0/0
ip address 72.28.*.* 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
!
!
interface Integrated-Service-Engine0/0
no ip address
shutdown
!
!
interface FastEthernet0/1/0
!
!
interface FastEthernet0/1/1
!
!
interface FastEthernet0/1/2
!
!
interface FastEthernet0/1/3
!
!
interface FastEthernet0/1/4
!
!
interface FastEthernet0/1/5
!
!
interface FastEthernet0/1/6
!
!
interface FastEthernet0/1/7
!
!
interface FastEthernet0/1/8
!
!
interface Dot11Radio0/5/0
no ip address
shutdown
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
!
!
interface Vlan1
ip address 192.168.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
!
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 72.28.*.*
!
no ip http server
no ip http secure-server
!
!
!
!
!
!
control-plane
!
!
!
!
voice-port 0/0/0
!
voice-port 0/0/1
!
voice-port 0/0/2
!
voice-port 0/0/3
!
voice-port 0/1/0
!
voice-port 0/1/1
!
voice-port 0/1/2
!
voice-port 0/1/3
!
voice-port 0/4/0
auto-cut-through
signal immediate
input gain auto-control
description Music On Hold Port
!
!
!
!
!
!
line con 0
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
login
!
end

Any help would be greatly appreciated.

THANKS!

[Uriah Erter]

I am experiencing similar issues in my envoironment, but for me the issue seems to be only 1 FQDN and only on 1 router in my network. When I ping time.nist.gov on this router it tries to resolve it to an ipv6 address which leads to the following:

router1#ping time.nist.gov

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 2610:20:6F15:15::27, timeout is 2 seconds:

% No valid route for destination
Success rate is 0 percent (0/1)

But when I ping other sites:

router1#ping yahoo.com
Translating "yahoo.com"...domain server (10.1.253.10)

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 98.138.253.109, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 108/134/152 ms

I have ipv6 disabled over my entire network and this is the only device experiencing this. Where is this coming from?

[devilleres]

Uriah,

Try the ping ip (host name) command instead of just ping.

If you want to ping an ipv6 host you use the ¨ping ipv6 (hostname)¨ command for ipv4: ping ip ...

Let me know how it went...

[ray1206]

I know this post is old but there was no resolution I could see. 
I recently solved this issue on an 1841 router by enabling (config)#ip domain-lookup

Hopefully this helps someone like me at some point. 

[Richard Burts]

It is an old post. But thanks for adding your experience with this issue. It may help others in the community.