07-06-2014 10:27 PM - edited 03-04-2019 11:17 PM
Here is below my diagram
Objective
1. ping every pc to other pc through static routes
Below Attached the configuration of Routers and also Diagram
Solved! Go to Solution.
07-07-2014 04:28 AM
This should do it:
R1
interface s1/0
ip address 10.1.1.1 255.255.255.252
interface s1/1
ip address 10.1.1.4 255.255.255.252
interface vlan 1
ip address 192.168.1.1 255.255.255.0
ip route 192.168.2.0 255.255.255.0 10.1.1.2
ip route 192.168.3.0 255.255.255.0 10.1.1.5
R2
interface s1/0
ip address 10.1.1.2 255.255.255.252
interface s1/1
ip address 10.1.1.9 255.255.255.252
interface vlan 1
ip address 192.168.2.1 255.255.255.0
ip route 192.168.1.0 255.255.255.0 10.1.1.1
ip route 192.168.3.0 255.255.255.0 10.1.1.10
R3
interface s1/0
ip address 10.1.1.5 255.255.255.252
interface s1/1
ip address 10.1.1.10 255.255.255.252
interface vlan 1
ip address 192.168.3.1 255.255.255.0
ip route 192.168.1.0 255.255.255.0 10.1.1.4
ip route 192.168.2.0 255.255.255.0 10.1.1.9
You will need to assign your hosts with the correct IP configuration as well as ensure clocking is provided by one router for the serial interfaces (if needed, I don't much use GNS3). Don't forget to no shut the interfaces.
07-07-2014 04:28 AM
This should do it:
R1
interface s1/0
ip address 10.1.1.1 255.255.255.252
interface s1/1
ip address 10.1.1.4 255.255.255.252
interface vlan 1
ip address 192.168.1.1 255.255.255.0
ip route 192.168.2.0 255.255.255.0 10.1.1.2
ip route 192.168.3.0 255.255.255.0 10.1.1.5
R2
interface s1/0
ip address 10.1.1.2 255.255.255.252
interface s1/1
ip address 10.1.1.9 255.255.255.252
interface vlan 1
ip address 192.168.2.1 255.255.255.0
ip route 192.168.1.0 255.255.255.0 10.1.1.1
ip route 192.168.3.0 255.255.255.0 10.1.1.10
R3
interface s1/0
ip address 10.1.1.5 255.255.255.252
interface s1/1
ip address 10.1.1.10 255.255.255.252
interface vlan 1
ip address 192.168.3.1 255.255.255.0
ip route 192.168.1.0 255.255.255.0 10.1.1.4
ip route 192.168.2.0 255.255.255.0 10.1.1.9
You will need to assign your hosts with the correct IP configuration as well as ensure clocking is provided by one router for the serial interfaces (if needed, I don't much use GNS3). Don't forget to no shut the interfaces.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide