04-26-2013 01:18 AM - edited 03-04-2019 07:44 PM
RSP720-3CXL-GE Standby Supervisor Running ONLY on 8G Fabric Speed
Hi Guys,
Good day.
Need your help on understanding why the standby supervisor of my Cisco 7600 router is running ONLY on 8G Fabric Speed:
#show fabric
show fabric active:
Active fabric card in slot 5
Backup fabric card in slot 6
show fabric mode:
Global switching mode is Truncated
dCEF mode is not enforced for system to operate
Fabric module is not required for system to operate
Modules are allowed to operate in bus mode
Truncated mode is allowed, due to presence of DFC, CEF720, Standby supervisor module
Module Slot Switching Mode
1 dCEF
2 Crossbar
3 Bus
5 Bus
6 Crossbar
7 Crossbar
8 Crossbar
9 dCEF
show fabric congestion management:
Fabric clear-block is off.
show fabric status all:
slot channel speed module fabric hotsync Standby Standby
status status support module fabric
1 0 20G OK OK Y(not-hot)
1 1 20G OK OK Y(not-hot)
2 0 8G OK OK N/A
5 0 20G OK OK Y(not-hot)
6 0 8G OK OK Y(not-hot)
7 0 20G OK OK Y(not-hot)
8 0 20G OK OK Y(not-hot)
8 1 20G OK OK Y(not-hot)
9 0 20G OK OK Y(not-hot)
9 1 20G OK OK Y(not-hot)
show fabric utilization all:
slot channel speed Ingress % Egress %
1 0 20G 16 5
1 1 20G 40 19
2 0 8G 3 0
5 0 20G 0 4
6 0 8G 8 8
7 0 20G 3 15
8 0 20G 8 7
8 1 20G 12 16
9 0 20G 0 0
9 1 20G 9 25
show fabric errors all:
Module errors:
slot channel crc hbeat sync DDR sync
1 0 0 0 0 0
1 1 0 0 0 0
2 0 0 0 0 0
5 0 0 0 0 0
6 0 0 0 0 0
7 0 0 0 0 0
#show module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 8 CEF720 8 port 10GE with DFC WS-X6708-10GE SAL1430xxxx
2 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL0922xxxx
3 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAL0905xxxx
4 11 7600 ES+ 76-ES+XC-20G3CXL SAL1653xxxx
5 2 Route Switch Processor 720 (Active) RSP720-3CXL-GE JAE1211xxxx
6 2 Route Switch Processor 720 (Hot) RSP720-3CXL-GE JAE1227xxxx
7 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1228xxxx
8 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1138xxxx
9 2 7600 ES+ 76-ES+XT-2TG3CXL SAL1601xxxx
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 xxxx.xxxx.xxxx to xxxx.xxxx.xxxx 2.2 12.2(18r)S1 12.2(33)SRD4 Ok
2 xxxx.xxxx.xxxx to xxxx.xxxx.xxxx 10.1 7.2(1) 8.7(0.22)SRD Ok
3 xxxx.xxxx.xxxx to xxxx.xxxx.xxxx 3.1 5.4(2) 8.7(0.22)SRD Ok
4 xxxx.xxxx.xxxx to xxxx.xxxx.xxxx 1.6 Unknown Unknown PwrDown
5 xxxx.xxxx.xxxx to xxxx.xxxx.xxxx 5.2 12.2(33r)SRC 12.2(33)SRD4 Ok
6 xxxx.xxxx.xxxx to xxxx.xxxx.xxxx 5.2 12.2(33r)SRC 12.2(33)SRD4 Ok
7 xxxx.xxxx.xxxx to xxxx.xxxx.xxxx 3.2 12.2(18r)S1 12.2(33)SRD4 Ok
8 xxxx.xxxx.xxxx to xxxx.xxxx.xxxx 2.6 12.2(14r)S5 12.2(33)SRD4 Ok
9 xxxx.xxxx.xxxx to xxxx.xxxx.xxxx 1.5 12.2(33r)SRD 12.2(33)SRD4 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Distributed Forwarding Card WS-F6700-DFC3CXL SAL1xxxxxxx 1.6 Ok
4 7600 ES+ DFC XL 7600-ES+3CXL SAL1652xxxx 1.3 PwrDown
4 7600 ES+ 1x10GE XFP 10x1GE 7600-ES+20C SAL1653xxxx 1.1 PwrDown
5 Policy Feature Card 3 7600-PFC3CXL JAE121xxxxx 1.0 Ok
5 C7600 MSFC4 Daughterboard 7600-MSFC4 JAE1222xxxx 1.1 Ok
6 Policy Feature Card 3 7600-PFC3CXL JAE1228xxxx 1.0 Ok
6 C7600 MSFC4 Daughterboard 7600-MSFC4 JAE1228xxxx 1.1 Ok
7 Centralized Forwarding Card WS-F6700-CFC SAL1227xxxx 4.1 Ok
8 Centralized Forwarding Card WS-F6700-CFC SAL1139xxxx 4.0 Ok
9 7600 ES+ DFC XL 7600-ES+3CXL SAL1552xxxx 1.2 Ok
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
3 Pass
4 Not Applicable
5 Pass
6 Pass
7 Pass
8 Pass
9 Pass
Thanks,
Gene
08-06-2019 10:28 AM
Hi, I have the same issue.
sh fabric switching-mode
Global switching mode is Compact
dCEF mode is not enforced for system to operate
Fabric module is not required for system to operate
Modules are allowed to operate in bus mode
Truncated mode is allowed, due to presence of DFC, CEF720, Standby supervisor module
Module Slot Switching Mode
1 Crossbar
2 Crossbar
3 Crossbar
4 Crossbar
5 dCEF
6 Crossbar
7 dCEF
8 dCEF
9 Crossbar
mez41-core#sh fabric
show fabric active:
Active fabric card in slot 5
Backup fabric card in slot 6
show fabric mode:
Global switching mode is Compact
dCEF mode is not enforced for system to operate
Fabric module is not required for system to operate
Modules are allowed to operate in bus mode
Truncated mode is allowed, due to presence of DFC, CEF720, Standby supervisor module
Module Slot Switching Mode
1 Crossbar
2 Crossbar
3 Crossbar
4 Crossbar
5 dCEF
6 Crossbar
7 dCEF
8 dCEF
9 Crossbar
show fabric congestion management:
Fabric clear-block is off (operational).
Fabric clear-block is off (configured).
show fabric status all:
slot channel speed module fabric hotsync Standby Standby
status status support module fabric
1 0 20G OK OK N/A
1 1 20G OK OK N/A
2 0 20G OK OK N/A
2 1 20G OK OK N/A
3 0 20G OK OK N/A
3 1 20G OK OK N/A
4 0 20G OK OK N/A
4 1 20G OK OK N/A
5 0 20G OK OK N/A
6 0 8G OK OK N/A
7 0 20G OK OK N/A
7 1 20G OK OK N/A
8 0 20G OK OK N/A
8 1 20G OK OK N/A
9 0 20G OK OK N/A
9 1 20G OK OK N/A
show fabric utilization all:
slot channel speed Ingress % Egress %
1 0 20G 2 5
1 1 20G 1 4
2 0 20G 2 3
2 1 20G 1 2
3 0 20G 6 1
3 1 20G 2 5
4 0 20G 0 2
4 1 20G 2 6
5 0 20G 0 0
6 0 8G 0 0
7 0 20G 26 9
7 1 20G 5 6
8 0 20G 21 21
8 1 20G 15 15
9 0 20G 1 5
9 1 20G 3 1
Is it ok, that standby supervisor running on 8g fabric capacity?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide