So i have the following topology-
ISP-RT-1 has a default route pointing to 192.168.20.1
Image being used is - vios-adventerprise9-m.SPA.159-3.M6
Some show commands-
ISP-RT-1#show ip bgp 0.0.0.0
BGP routing table entry for 0.0.0.0/0, version 2
Paths: (1 available, best #1, table default)
Advertised to update-groups:
3
Refresh Epoch 1
Local
192.168.20.1 from 0.0.0.0 (1.1.1.1)
Origin IGP, metric 0, localpref 100, weight 32768, valid, sourced, local, best
rx pathid: 0, tx pathid: 0x0
Now im trying to aadvertise this to the 3 ibgp peers (1 of them not shown in the pic but its just a direct point to point) and it doesnt work at all-
ISP-RT-1#show running-config | section bgp
router bgp 65312
bgp log-neighbor-changes
network 0.0.0.0
neighbor 65.30.24.1 remote-as 65312
neighbor 65.30.24.5 remote-as 65312
neighbor 65.30.24.9 remote-as 65312
ISP-RT-1#show ip bgp summary
BGP router identifier 1.1.1.1, local AS number 65312
BGP table version is 2, main routing table version 2
1 network entries using 144 bytes of memory
1 path entries using 84 bytes of memory
1/1 BGP path/bestpath attribute entries using 160 bytes of memory
0 BGP route-map cache entries using 0 bytes of memory
0 BGP filter-list cache entries using 0 bytes of memory
BGP using 388 total bytes of memory
BGP activity 1/0 prefixes, 1/0 paths, scan interval 60 secs
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
65.30.24.1 4 65312 9 10 2 0 0 00:04:59 0
65.30.24.5 4 65312 9 11 2 0 0 00:04:49 0
65.30.24.9 4 65312 9 11 2 0 0 00:04:37 0
If i look at the routing table on say ISP-RT-2 it doesnt learn the default route, what am i doing wrong?
ISP-RT-2#show ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
a - application route
+ - replicated route, % - next hop override, p - overrides from PfR
Gateway of last resort is not set
2.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 2.2.2.0/24 is directly connected, Loopback0
L 2.2.2.2/32 is directly connected, Loopback0
65.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 65.30.24.0/30 is directly connected, GigabitEthernet0/1
L 65.30.24.1/32 is directly connected, GigabitEthernet0/1
Its the same on the other 2 routers as well and they do not learn the default route, so yeah no idea whats going on.
Ive researched online and everywhere i look they say all i need is a "network 0.0.0.0" statement which i tried as you can see but yeah doesnt work.
Thank You
from CCIE v5 vol. 2 by Narbik, Vinston, Cisco Press.
Regards, ML
**Have fun labbing!!!***
***Please Rate All Helpful Responses ***
